Sony UWP-C1/C2, UWP-S1/S2, UWP-X1/X2 Sample configuration of a PA system

Sample configuration of a PA system

Hand-held microphone (UTX-H1)

AN-820 UHF antenna

Diversity tuner module (URX-M1)

Body-pack transmitter (UTX-B1)

To DVD player, PC,
or VTR, etc.	SRP-X700P
	SRP-X700P
	Powered Mixer

1 Lavalier microphone (supplied)	Diversity tuner
2 BNC cable	module (URX-M1)
3 XLR cable
4 XLR cable or pin cable
*1 WD-820A Antenna Divider
*2 MB-806A Tuner Base Unit
*3 SRP-X100 Audio Mixer

Contents

UWP-C1/C2 UWP-S1/S2 UWP-X1/X2 Page Table of Contents ConfigurationConfigurationof the Packagesof the Packages Configuration of the Packages UWP-C1 Body-packtransmitter Portable diversity tuner UWP-C2 Hand-heldmicrophone (UTX-H1)(1) Configuration of the Packages UWP-S1 Half-racksize diversity tuner (URX-R1)(1) UWP-S2 UWP-X1 Diversity tuner module (URX-M1)(1) UWP-X2 Features UWP-C1 UWP-C2 UWP-S1 UWP-S2 UWP-X1 UWP-X2 Precautions Parts Identification Parts Identification 5+ (+ selection) / – (– selection/ reset) buttons 6Battery compartment Accommodates two LR6 (size AA) alkaline batteries 7SET button 8POWER switch 6SET button Portable diversity tuner (URX-P1) 1Antennas a/b 2MONITOR connector (3.5-mmdiameter stereo mini jack) RF (radio frequency) indications CBATT (battery) indication Shows the battery condition DGP (group)/CH (channel) indication 9OUTPUT (audio output) connector (3.5-mmdiameter stereo mini jack) Half-racksize diversity tuner (URX-R1) 1POWER switch 2Antennas a/b 3MONITOR connector (phone jack) 7RF (radio frequency) indicator Indicates the strength of the RF input signal 8SET button TUNER OUTPUT (audio output) connector (XLR type) 0LEVEL (audio output level) switch qs DC IN 9V (DC power input) connector 4+ (+ selection) / – (– selection/ reset) buttons Body-packtransmitter (UTX- B1)/portable diversity tuner (URX-P1) Battery indication Notes on batteries Attachment and Installation Procedures Attaching the microphone Attaching the holder clip to the microphone Attaching the wind screen to the microphone Attaching the belt clip Attaching the microphone holder Connecting the supplied conversion cable to the OUTPUT connector Attaching the shoe mount adapter stand adapter Installing a diversity tuner module (URX-M1)into an MB- 806A Tuner Base Unit Installing a diversity tuner module (URX-M1)into an SRP-X700PPowered Mixer Settings Setting the reception channel The procedure below is the same for all UWP series tuners (URX-P1/R1/M1) To selct the channel by frequency indication Setting the attenuation level of the audio input Do the following while there is no signal transmission Do the following while there is signal transmission Resetting the accumulated battery use time indication For transmitters (UTX-B1/H1) 1-b For the portable diversity tuner (URX-P1) Setting the monitor level (portable diversity tuner (URX-P1)only) Operation If noise is heard System Configurations System Configurations Sample configurations for AV presentations Sample configuration of a PA system Error Messages Troubleshooting Troubleshooting Specifications Items common to all transmitters Body-packtransmitter (UTX-B1) Items common to all tuners Portable diversity tuner (URX-P1) Half-racksize diversity tuner (URX-R1) Diversity tuner module (URX- M1) Appendix Guidance on the use of a multi-channelsystem Group for transmitter and tuner Groups for tuner AC adapter for use with the URX-R1 •Specifications •The size of the DC output connector (DC jack)