Model SB1029 | P A R T S | For Machines Mfg. Since 8/09 |
Machine Labels
301
MODEL SB1029
6" x 18" SURFACE GRINDER
Serial No:
!WARNING!
MFG Date:
NOTICE
Only trained and properly supervised personnel are allowed to operate this machine. If safe operation procedures are not clearly understood, request additional training from a supervisor before beginning operation.
324
•Clnotice
326
325
Motor:
Table Surface Size:
Spindle Speed: 3450 RPM
Longitudinal Travel:
Cross Travel:
Max. Distance Wheel To Table: 15.3"
Maximum Grinding Length:
Maximum Grinding Width:
Vertical Handwheel Revolution: 0.05"
Crossfeed Handwheel Revolution: 0.2"
Grinding Wheel: 7"D X 1/2"W X
Spindle Arbor: 1"D X 7.5° Taper
Floor to Table Height: 40"
Weight: 1672 Lbs.
Made in Taiwan to South Bend Specifications
TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY WHILE USING THIS MACHINE:
1.Read and understand manual before starting.
2.Always wear eye protection and respirator.
3.Always balance and dress wheel before use.
4.Never place hands near moving machine parts or workpiece.
5.Never use hands to hold workpiece while grinding.
6.Inspect wheel before each use. Never use grinding wheels that have been dropped or have chips or cracks. Inspect wheel before each use.
7.Do not wear loose clothing, gloves or jewelry. Secure long hair and button all long sleeve shirts.
8.Disconnect power before servicing, setting up or adjusting.
9.Do not use grinding wheels rated lower than 3450 RPM.
10.Do not operate under the influence of drugs or alcohol.
11.Make sure machine is properly adjusted, set up, and workpiece is clamped before starting motor.
12.Keep floor area around the grinder clean and dry.
13.Never leave the machine running unattended.
302
NOTICE
TIPS FOR BEST GRINDING RESULTS:
•Make sure the grinding wheel is balanced before use.
•Select an appropriate grinding wheel according to the workpiece material.
•Keep a thin coat of oil on the spindle nose and wheel flange to prevent rust.
•Never use compressed air to clean the machine. Doing so will force metal chips into the table ways.
•Keep longitudinal handwheel drive cable properly tightened.
•Empty, clean, and refill oil reservoir every
•Adjust oil flow as necessary to maintain smooth operation of all moving parts.
•Clean dust collection at least weekly, or any time you notice a drop in suction.
305
306
1 2 3 4
323
322
321
x4 |
NOTICE
Before using the machine, lift the table and remove the four plastic shipping support blocks from both ends. Save these blocks for future transport of the machine.
320
!WARNING!
303304
!WARNING!
TIPPING HAZARD DO NOT place a heavy object at one end of the table. Doing so may cause the table to tip, resulting in personal injury or damage to machine.
NOTICE
Before using machine, remove this cover and make sure the lubrication tank is filled with Mobil Vacuoline 1405 or equivalent oil (ISO 32 Way Oil) to provide lubrication to the ways.
1.Vertical Leadscrew
2.Cross Leadscrew
3.Longitudinal & Cross Slideways
4.Pressure Discharge
•Turning valve counterclockwise reduces oil flow.
•Turning valve clockwise increases oil flow.
•To restore factory settings:
Valve 1: Turn fully counterclockwise (full flow).
Valves 2 & 3: Turn clockwise until snug, then back 1 turn.
Valve 4: Turn clockwise until snug, then loosen unti steady drip is observed (about 3 drops per second).
EYE/FACE/LUNG INJURY HAZARD Always wear a face shield and respirator
when using this
NOTICE
If excessive play develops in the longitudinal hand- wheel, the cable drive can be tightened. See your Owner’s Manual for details.
equipment.
319
318
317316
| 310 |
| 220V |
| |
| 311 |
! | 307 |
!WARNING!
POISON/
BIOHAZARD Refer to the cutting fluid manufacturer’s Material Safety Data Sheets (MSDS) for safety information.
| 313 | ! WARNING! |
| INJURY/SHOCK | |
| HAZARD | |
! WARNING! | To avoid shock or | |
| accidental starting, | |
INJURY HAZARD |
| disconnect power |
Do not use machine if |
| before adjusting or |
you have not read the |
| servicing machine. |
manual. Visit southbendlathe.com or
call | 312 |
get a manual. |
|
314
