Operating Precautions | SUPER MICRO Computer 5015M-U, 5015M-NT

SUPERSERVER 5015M-UR/5015M-U/5015M-NTR/5015M-NT User's Manual

4-4 Operating Precautions

!

Care must be taken to assure that the chassis cover is in place when the 5015M- UR/5015M-U/5015M-NTR/5015M-NT is operating to ensure proper cooling. Out of warranty damage to the 5015M-UR/5015M-U/5015M-NTR/5015M-NT system can occur if this practice is not strictly followed.

Figure 4-1. Installing the Onboard Battery

LITHIUM BATTERYLITHIUM BATTERY

	OR
BATTERY HOLDER	BATTERY HOLDER

4-4

Image 34

SUPER MICRO Computer 5015M-UR, 5015M-NTR user manual Operating Precautions, Installing the Onboard Battery

Contents

Super Manual Revision 1.0d Release Date April 15 About This Manual PrefaceManual Organization Advanced Chassis Setup System SafetyAdvanced Serverboard Setup Bios Preface Table of Contents System Safety Advanced Serverboard Setup Advanced Chassis Setup Bios Appendices Page Chapter Introduction Overview Memory Serverboard FeaturesProcessors UIO 5015M-UR Server Chassis Features Backplane PCI Expansion SlotsFront Control Panel Cooling System Intel 3010 Chipset System Block Diagram Europe Contacting SupermicroHeadquarters Asia-Paciﬁc Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Installing the Inner Rails Installing the System into a RackIdentifying the Sections of the Rack Rails Installing the Outer Rails Locking Tabs Installing the Server into the Rack Installing the Server into a Rack Installing the Server into a Telco Rack Installing the Server into a Telco Rack Checking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Chapter System Interface Control Panel Buttons Control Panel LEDs Universal Information LED States Sata Drive Carrier LEDs Page Chapter System Safety Electrical Safety Precautions General Safety Precautions ESD Precautions Operating Precautions Installing the Onboard Battery Handling the Serverboard Chapter Advanced Serverboard SetupPrecautions Unpacking Processor and Heatsink Installation Installing the ProcessorPage Installing the Heatsink Removing the Heatsink Connecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel Front Control Panel Header Pins JF1 Dimm Installation Installing MemoryI/O Ports Installing Dimm into Slot Memory Support Adding PCI Cards PCI card installationPCI Expansion Slots Serverboard Details Super Pdsmu Layout Pdsmu Quick Reference Jumper Description Default SettingConnector Description LEDs Description Processor Power Connector Connector DeﬁnitionsATX Power Connector Power LED HDD LED Universal Information LED Power Button Power Fail LEDReset Button Universal Serial Bus USB0/1 Serial Ports Universal Serial Bus HeadersFan Headers ATX PS/2 Keyboard and PS/2 Mouse Ports Speaker ConnectorChassis Intrusion Wake-On-LAN Alarm Reset JAR Power SMB I2C ConnectorPower Supply Fail Wake-On-Ring LAN1/2 Ethernet Ports Explanation Jumpers Jumper SettingsVGA Enable/Disable Cmos Clear Watch Dog Enable/Disable LAN Enable/DisablePower Force On Enable/ Disable Onboard Indicators LAN1/LAN2 LEDs Floppy Connector Floppy, IDE and Sata Drive Connections IDE Connector Sata PortsPage Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front and Rear Views System Fan Failure Installing a new fanSystem Fans Replacing System Fans Drive Bay Installation/Removal Removing the Front Bezel Accessing the Drive Bays Removing the Front Bezel Sata Drive Installation Mounting a Sata drive in a drive carrier Installing/removing hot-swap Sata drives Removing a Sata Drive from the Server DVD-ROM and Floppy Drive Installation Removing/Replacing the Power Supply Power SupplyPower Supply Failure 5015M-UR/5015M-NTR 5015M-U/5015M-NT Removing/Replacing the Power Supply Page Starting the Setup Utility System BiosHow To Change the Conﬁguration Data Chapter Main Bios Setup Running SetupPress the Delete key to enter Setup Main Bios Setup Menu Main Setup Features Serial ATA Sata RAID Enable Native Mode OperationSata Controller Mode ICH RAID Code Base Available when Sata RAID is Enabled Ultra DMA Mode LBA Mode ControlTransfer Mode Type Advanced Setup Cache Video Bios Area Power Loss ControlMemory Cache Cache System Bios Area Resume On Modem Ring Cache Extended Memory Reset Conﬁguration DataCache Base 512K-640K Discrete Mtrr Allocation Large Disk Access Mode Enable MasterLatency Timer Clock Spectrum Feature Advanced Processor Options USB FunctionLegacy USB Support CPU Speed Device Conﬁguration C1 Enhanced Mode Available when supported by the CPUSet Maximum Extended CPUID=3 KBC Clock Input Interrupt Serial Port aBase I/O Address Serial Port B Event Log Capacity DMI Event LoggingEvent Log Validity View DMI Event Log Baud Rate Console RedirectionCOM Port Address Console Type Voltage Monitoring CPU Temperature ThresholdHardware Monitor Logic Fan Speed Control Modes Set Supervisor Password Supervisor Password IsUser Password Is Set User Password Password on Boot BootBoot Priority Order/Excluded from Boot Orders Exit Appendix a Bios Post Messages Real time clock error System Cmos checksum bad Default conﬁguration usedSystem timer error Check date and time settings Allocation Error for device System cache error Cache disabledFail-Safe Timer NMI Failed Entering Setup Device IRQ conﬂict PS/2 Mouse Boot Summary ScreenInvalid System Conﬁguration Data Nnnn kB Extended RAM Passed System Bios shadowed Press F1 to resume, F2 to Setup, F3 for previousPress F2 to enter Setup Video Bios shadowedPage Terminal Post Errors Appendix B Bios Post CodesRecoverable Post Errors Post Code Description Post Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Page Important Notes to the User Intel HostRAIDIntroduction to Serial ATA and Parallel ATA Serial ATA Sata RAID Conﬁgurations Intel Matrix Storage Using the Intel ICH7R Sata RAID Utility Program Creating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting a RAID Volume Resetting to Non-RAID and Resetting a RAID HDD Exiting the Intel Matrix Storage Manager Utility Installing Windows XP/2000/2003 for RAID Systems New Operating System-Windows XP/2000/2003 Installation Appendix D Adaptec HostRAID Setup Guidelines Introduction to the Intel ICH7R I/O Controller Hub Conﬁguring the Adaptec Sata RAID Using the Array Conﬁguration Utility ACU Using the Adaptec RAID Conﬁguration Utility ARCAdaptec Embedded Sata with HostRAID Controller Driver Managing Arrays Conﬁguring Disk Drives To conﬁgure a disk drivePage Page Creating Arrays To create an array Assigning Array Properties To assign properties to the new arrayPage Adding a Bootable Array Deleting a Bootable Array Adding/Deleting Hotspares Viewing Array Properties Rebuilding Arrays To Rebuild an array Deleting Arrays RAID 1 only-the following prompt is also displayed Using the Disk Utilities To access the disk utilities To format a disk To verify disk media To Exit the Adaptec RAID Conﬁguration Utility Installing the Adaptec ICH7R Driver and the OS Appendix E System Speciﬁcations Serverboard WeightPower Supply Chassis Operating Environment Regulatory Compliance