Installing the Heatsink | SUPER MICRO Computer MBDX7DA3O guide

X7DA3+ User's Manual

Installing the Heatsink

CEK Heatsink Installation

CEK Passive Heatsink

1.Do not apply any thermal grease to the heatsink or the CPU die-the required amount has already been applied.

2.Place the heatsink on top of the CPU so that the four mounting holes are aligned with

those on the retention mechanism.

Screw#1

Screw#2

3. Screw in two diagonal screws (ie the #1 and the #2 screws) until just snug (-do not fully tighten the screws to avoid possible

damage to the CPU.)

Screw#1

4. Finish the installation by fully tightening all four screws.

Screw#2

2-4

Image 24

SUPER MICRO Computer MBDX7DA3O user manual Installing the Heatsink, CEK Heatsink Installation

Contents

Super Page About This Manual Manual OrganizationConventions Used in the Manual Table of Contents Table of Contents Troubleshooting BiosAppendices Checklist Overview Contacting Supermicro Headquarters EuropeAsia-Paciﬁc X7DA3+ Image X7DA3+ Motherboard Layout SAS ACT4-7 LEDs Jumper Description Default Setting Quick Reference X7DA3+ Motherboard Features Dimensions Onboard I/OOther CD/Diskette Utilities Block Diagram of the 5000X Greencreek Chipset MCH Xeon Dual Core Processor Features Chipset OverviewXeon Dual Core Processors Special Features PC Health Monitoring Acpi Features Slow Blinking LED for Suspend-State IndicatorMain Switch Override Mechanism CPU Overheat LED and Control Power Supply Super I/OExternal Wake-On-LAN Page Page Motherboard Installation PrecautionsStatic-Sensitive Devices Unpacking Processor and Heatsink Installation Installing the LGA771 ProcessorPage Installing the Heatsink CEK Heatsink Installation Uninstalling the Heatsink Installing DIMMs Dimm Installation See FigureMemory Support Installing and Removing DIMMs Top View of DDR2 FBDPossible System Memory Allocation & Availability Control Panel Connectors/IO Ports Back Panel Connectors/IO Ports JF1 Header Pins Front Control Panel Power LED Power LED Pin Deﬁnitions JF1Front Control Panel Pin Deﬁnitions NMI Button NMI Button Pin Deﬁnitions JF1 NIC1/NIC2 LED Indicators Pin# Deﬁ nition 13 +5V HD ActivePin# Deﬁ nition Vcc 10/12 Ground Power Fail LED Overheat/Fan Fail LED OHOH/Fan Fail LED PWR Supply Fail Reset Button Power ButtonReset Button PWR Button Reset Button Pin Deﬁnitions JF1 Connectors and Headers ATX Power ConnectorProcessor Power Connector Universal Serial Bus USB Chassis IntrusionBack Panel USB USB0/1/2/3 Front Panel USB Pin Deﬁnitions USB4 Fan Headers Fan Header Pin Deﬁnitions Fan1-8 ATX PS/2 Keyboard and PS/2 Mouse Ports Serial PortKeyboard/Mouse PS/2 Keyboard Mouse Port Pin Deﬁnitions Wake-On-Ring Wake-On-LANWake-On-Ring Pin Deﬁnitions Wake-On-LAN Pin Deﬁnitions Power LED/Speaker Speaker ConnectorGlan 1/2 Giga-bit Ethernet Ports GLAN1/2 PWR LED/Speaker Power Fault PWR Supply Failure Power Fault Overheat LEDOverheat LED/Fan Fail JOH1 Power SMB I2 C Connector SMB Header Pin DeﬁnitionsPin# Deﬁ nition Data Ground Clock No Connection Pin# Deﬁ nition Clock Data PWR Fail Ground +3.3V Compact Flash Card PWR Connector Compact Flash Card PWR ConnectorSgpio Headers Compact Flash PWR B. Sgpio CD Connector High Deﬁnition Audio HD AudioHD Audio CD1 CD1 Pin Deﬁnition Jumper Settings Glan Enable/DisableGlan Port1 Enable Glan Port2 Enable Glan Enable Watch Dog Enable/Disable Clear Cmos Watch Dog EnableWatch Dog Jumper Settings JWD Cmos Clear 3rd PWR Supply PWR Fault Detect J3P SAS Controller Enable Disable3rd PWR Fail SAS Enable 3rd PWR Supply PWR Fault Jumper Settings Alarm Reset Compact Flash Master Slave Select Alarm ResetAlarm Reset Compact Flash Master/Slave Select JI2C 1/2 JI2C 3/4 SAS Enable SMBus to PCI-X/PCI-Exp Slots Jumper SettingsJumper Setting Deﬁ nition Pins Enabled Disabled Default SMB to PCI-X/PCI-E Slots Onboard Indicators Onboard Power LEDGlan LEDs Onboard SAS Activity LED Indicators SAS Act. #0-#3 LEDs SAS Act. #4-#7 LEDsAct. #4-#7 LEDs Act. #0-#3 LEDs Parallel Printer Port Parallel Port Floppy Connector Simlp Ipmi SlotFloppy IDE Connectors IDE#1 IDE#2 Compact Flash SAS Connectors SAS #0-#3 SAS #4-#7 Troubleshooting Procedures Before Power OnNo Power No Video Technical Support Procedures Losing the System’s Setup ConﬁgurationMemory Errors Frequently Asked Questions Returning Merchandise for Service System Bios How To Change the Conﬁguration DataStarting the Setup Utility Running Setup Main Bios SetupPress the Delete key to enter Setup Main Setup Features Bios DateSystem Time System Date Type Multi-Sector Transfer LBA Mode Control Transfer ModeUltra DMA Mode Native Mode Operation Advanced Setup ICH RAID Code Base Available when Sata RAID is enabledSata Ahci Available when Sata RAID is disabled System Memory Boot Features QuickBoot ModeQuiet Boot Post Errors Power Loss Control Memory Cache Cache System Bios AreaCache Video Bios Area Watch Dog Default Primary Video Adapter Cache Extended MemoryDiscrete Mtrr Allocation PCI Conﬁguration Emulated IRQ Solutions PCI Parity Error ForwardingPCI Fast Delayed Transaction Reset Conﬁguration Data Enable Master Latency TimerLarge Disk Access Mode Serr Signal Condition Memory Branch Mode High Temperature Dram OperationBranch 0 Rank Sparing/Branch 1 Rank Sparing Branch 0 Rank Interleaving/Branch 1 Rank Interleaving Crystal Beach Features Clock Spectrum FeatureSnoop Filter HD High Deﬁnition Audio Controller Frequency Ratio Available when supported by the CPU Core-Multi-Processing Available when supported by the CPUMachine Checking Available when supported by the CPU Thermal Management 2 Available when supported by the CPU Hardware Prefetch Available when supported by the CPU Direct Cache Access Available when supported by the CPUDCA Delay ClocksAvailable when supported by the CPU Intel Eist Support Available when supported by the CPU Device Conﬁguration KBC Clock InputSerial Port a Base I/O Address DMA Channel Floppy Disk ControllerDMI Event Logging Event Log Validity Console Redirection COM Port AddressBaud Rate Console Type CPU Temperature Threshold Hardware Monitor LogicVoltage Monitoring Fan Speed Control Modes System Event Logging Clear System Event LoggingExisting Event Log Number Event Log Control System Event Log/System Event Log List Mode OS Boot Watch DogTimer for Loading OS Minutes Time Out Option Realtime Sensor Data Security Settings Supervisor Password IsUser Password Is Set Supervisor Password Boot Settings Password on BootBoot Priority Order/Excluded from Boot Orders Exit Page Keyboard error Keyboard locked Unlock key switchMonitor type does not match Cmos Run Setup System battery is dead Replace and run Setup System Cmos checksum bad Default conﬁguration used System timer errorReal time clock error Check date and time settings System cache error Cache disabled Fail-Safe Timer NMI FailedAllocation Error for device Entering Setup PS/2 Mouse Boot Summary Screen Invalid System Conﬁguration DataDevice IRQ conﬂict Nnnn kB Extended RAM Passed Press F1 to resume, F2 to Setup, F3 for previous Press F2 to enter SetupSystem Bios shadowed Video Bios shadowedPage Appendix B Post Error Beep Codes Page Using the Adaptec RAID Conﬁguration Utility Adaptec Embedded SAS with HostRAID Controller Using the Array Conﬁguration Utility Managing Arrays Viewing Array Properties Deleting ArraysRAID 1 only-the following prompt is also displayed Creating Arrays To create an array Assigning Array Properties To assign properties to the new arrayNo Init Creating a RAID 0 on new drives InitPage Adding a Bootable Array To make an array bootable Deleting a Bootable Array To delete a bootable array Adding/Deleting Hotspares To Add a HotSpare DriveTo Delete a HotSpare Drive Initializing Disk Drives Page Page Rebuilding Arrays To Rebuild an array Using the SerialSelect Utility to Conﬁgure SAS Settings To access the SAS utilities To Set Controller Conﬁguration To Set Physical Conﬁguration Using the Disk Utilities To access the disk utilitiesFollowing options are available To Exit Adaptec RAID Conﬁguration Utility Installing the ESB2/SAS Driver and the Operating System Page Introduction to Serial ATA and Parallel ATA Important Notes to the UserSerial ATA Sata Introduction to the Intel ESB2 Serial RAID Controller Hub Intel HostRAID Conﬁgurations Intel Matrix Storage Using the Intel ESB2 Sata RAID Utility Program Creating, Deleting and Resetting RAID Volumes Creating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting RAID Volume Resetting to Non-RAID and Resetting a RAID HDD Exiting the Intel Matrix Storage Manager Utility New Operating System-Windows XP/2000/2003 Installation Appendix E Installing Other Software Programs and Drivers Installing Other Software Programs and Drivers Conﬁguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control