Status Display, RS-232 Baud Rate | SUPER MICRO Computer MIIC-203

Command: Ctrl/R,Ctrl/R,Ctrl/R	‘iPort Reset
Response. *	‘iPort/AFM Ready
Default Setting:	None

Status Display

This command displays current iPort/AFM status.

Command: //[CR] 'Status Display Response:

iPort/AFM I2C Host Adapter w/ASCII Fast Mode Interface Vxx.xx Copyright © xxxx, Micro Computer Control Corp.

Visit our Web Site at: http://www.mcc-us.com

RS-232 Baud Rate (19.2KHz) Destination I2C Slave Address (4EH) Echo/Prompt (Disabled)

Flow Control (XON/XOFF) Hex Only Display (Enabled) I2C Connection (Closed)

General Call (Enabled)

iPort’s own Slave Address (6EH) I2C Bus Clock Rate (100 KHz) iNterrupt Signal (Released)

I2C Bus Time-oUt (10000 msec)

RS-232 Baud Rate

This command sets the RS-232 Baud Rate. (0=19.2k, 1=57.6k, 2= 115.2k)

Command: /B[012][CR]	'Set RS-232 Baud Rate
Response 1: /BC0[CR]	'Baud Change Complete
Response 2: /BC1[CR]	'Baud Change Complete
Response 3: /BC2[CR]	'Baud Change Complete
Response 3: /I89[CR]	'Invalid Command Argument
Default Setting: /B0[CR]

34

Image 33

SUPER MICRO Computer MIIC-203 manual Status Display, RS-232 Baud Rate

Contents

479,12 Introduction Page Table of Contents Programmer’s Reference Ascii Command Interface Definitions Page Model MIIC-203 Part Overview RS-232 to I2C Host Adapter Ascii Fast Mode Interface System Requirements RS-232 Serial Port ConnectorInterconnects Packing Slip DB-25 Serial Port Pinout +5VDC Power Jack INT, Interrupt Signal Control I2C Interface Connector Connecting to an SMBus System Connecting to a 3.3v SystemHardware Set-Up Pull-up Resistors IPort Utility Pack for Windows Introduction to Utility Pack IPort Message Center IPort Message Manager Software Installation Page I2C Message Operations Page Page Page Starting the program Select iPort DeviceEstablish iPort Link Basic Set-up Advanced Set-up Diagnostic Set-up iPort Only To Master Transmit Data Sending Messages Master Operations To Master Receive Data Uninstalling iPort Utility Pack To Slave Transmit a messageTo Slave Receive a message Programmer’s Reference IPort/AFM Quick Start Command Description IPort/AFM Ascii Text Interface Commands Synchronous Interface Events IPort/AFM Reset RS-232 Baud Rate Status Display Set Destination I2C Slave Address Close I2C ConnectionEcho/Prompt Control Flow Control Hex Only Display Control I2C General Call Control Command Menu Display Set iPort/AFM’s Own I2C Slave AddressI2C Bus Clock Rate Control Open I2C Connection Interrupt Signal Control/Status Master Read Message Slave Transmit Message Master Transmit Message EXtended Commands requires V2.00+ Set I2C Bus Time-oUt in msecDisplay Firmware Version requires V2.00+ Page Issue a Read WCR command to a Xicor X9241 at slave address Display Tx bYte Count requires V2.00+ Slave Transmit Request Asynchronous Interface EventsSlave Receive Complete General Call Receive Complete INterrupt Signal Assert INterrupt Signal ReleaseI2C Bus Time-out Detected IPort/AFM Prompts I2C Bus Error DetectedIPort/AFM Ready Slave Not Acknowledging Invalid iPort/AFM Command Invalid Command ArgumentIPort/AFM Connection Closed Slave Transmit Request Not Active IPort/AFM Initialization Example CodeMaster Receive Message Communication Event ProcessingPage Page Page Revision IPort/AFM Revision ReportAdditional Information Micro Computer Control Corporation Life Support Applications Limited Warranty Limitation of Remedies and Damages Appendix a