Manuals / TANDBERG / Computer Equipment / Network Card

TANDBERG MPS 200, MPS 800 manual 148, E1/T1 Network Interface Card IIC-8, PRI E1/T1 Pinout

Models: MPS 800 MPS 200

1 179
Download 179 pages 17.67 Kb
Page 148
Image 148

Network Interfaces

E1/T1 Network Interface Card (IIC-8) (1:3)

TANDBERG MPS ADMINISTRATOR GUIDE

Chassis

TANDBERG MPS 800

The TANDBERG MPS 800 has a 9U-19” rack-mountable chassis that can host up to 8 Media Processing Boards and 4 Network Interface Cards.

TANDBERG MPS 200

The TANDBERG MPS 200 has 3U-19” rack- mountable chassis that can host up to 2 Media Processing Boards and 2 Network Interface Cards.

Front Chassis

The TANDBERG MPS chassis is 19” rack- mountable. On the front of the chassis is a Liquid Crystal Display (LCD) for initial con- figuration and basic system information.

You will also find 4 Light Emitting Diodes (LEDs) for power status. The backplane of the chassis is provided with advanced CompactPCI technology for high speed communication between the boards. You will find 3 cooling fans in the lower front of the chassis.

Rear Chassis MPS 800

E1/T1 Network Interface Card (IIC-8)

E1/T1 Network Interface Card

Rear View

• The MPS 800 supports up to 4 E1/T1 Network Interface Cards.

The E1/T1 Card is equipped with

• The MPS 200 supports up to 2 E1/T1 Network Interface Cards.

PRI ports for ISDN interface:

• Each E1/T1 Interface Card gives 8 E1/T1 PRI ports.

• 8 x E1/T1 PRI ports (RJ-45)

• PRI ports/options are purchased in groups of 4 PRI ports.

Light Emitting Diodes (LEDs) for PRI

• The E1/T1 Interface Card is also used for G.703 Leased Line calls.

 

Port status, with 4 LEDs for each

ISDN Protocol

E1/T1 PRI port:

• Red – Layer 1 Red Alarm

• All 8 PRI ports on the same PRI card must use the same ISDN protocol

• Yellow – Layer 1 Yellow Alarm

and the same network interface (E1 or T1).

• Green – Layer 1 OK

• However, there is support for separate PRI protocols on each E1/T1 Inter-

• Red – D-Channel Down

face Card.

 

 

See next page for more information

Connecting the Card

about the LEDs.

 

• The E1/T1 Interface Card is installed in the rear of the chassis. See

Serial RS-232

the TANDBERG MPS 800 – E1/T1 interface cards on how the card is

 

installed.

 

•One Media Processing Board must be in front of each E1/T1 Interface Card.

•The Network Interface Card connects into the back of a Media Pro-

cessing Board by connecting to its J5-connector from the back of the

PRI E1/T1 Cable

chassis.

 

1

 

2

 

3

8 x E1/T1

PRI Ports

 

4

 

5

 

6

 

7

 

8

 

1

 

2

4 LED’s for

3

4

each PRI

5

8 7 6

Interface

-232

Serial

RS

RS-232

 

The TANDBERG MPS 800 is shipped with

2hot-swappable power units for configura- tions of 1 to 3 Media Processing Boards. If the unit has more than 3 Media Process- ing Boards the TANDBERG MPS 800 is equipped with 3 hot-swappable power units. The power units are installed at the back of the chassis. You will also find the power switch/connector at the back of the chassis.

Rear Chassis MPS 200

The TANDBERG MPS 200 is shipped with 1 power unit integrated in the chassis.

Network Clock

The card connected to Media Processing Board #1 provides the primary network clock for the unit.

When you have an E1/T1 Interface Card connected to this Media Processing Board, the command line interface command reconfigures which PRI-port this clock is taken from:

xConfiguration SystemClock Port <0,1-8>

•The value 0 is auto, meaning the first port with a clock.

•The value 1 - 8 tells the TANDBERG MPS to take the clock from that specific PRI-port.

PRI E1/T1 Cable

The cable of use should be a straight through configuration.

TANDBERG recommends al- ways using at least category 5 cabling.

PRI E1/T1 Pinout

PRI Pinout

1TIP RX

2RING RX

4RING TX

5TIP TX

Main

Table of

Introduction

Installation

Quick

Using

System

System

Gateway

MCU

Technical

Appendices

Contents

Setup

the MPS

Status

Configuration

Configuration

Configuration

Descriptions

 

 

 

 

D 13373.08

 

 

 

 

148

 

 

 

 

 

MPS

NOVEMBER 2007

 

 

 

 

 

 

 

 

 

Page 147 Page 149
Page 148
Image 148
TANDBERG MPS 200, MPS 800 manual 148, E1/T1 Network Interface Card IIC-8, PRI E1/T1 Pinout
Page 147 Page 149

MPS 800, MPS 200 specifications

The TANDBERG MPS 200 is an advanced multipoint conferencing solution designed to enhance communication and collaboration in various environments. Renowned for its robust performance and versatile features, the MPS 200 caters to businesses and organizations seeking to integrate video conferencing seamlessly into their operations.

One of the standout features of the MPS 200 is its ability to support high-definition video conferencing. Ensuring crystal-clear imagery, it accommodates various video standards, including H.264, allowing for efficient bandwidth usage without compromising quality. This makes it an excellent choice for organizations that require high-quality video for their meetings, presentations, or training sessions.

The MPS 200 also supports a wide range of participants, facilitating large-scale conferences with multiple endpoints. It can connect numerous participants simultaneously, allowing teams from different locations to collaborate effectively. This scalability is essential for businesses that frequently host meetings with various stakeholders, enabling seamless interaction and engagement.

Another noteworthy technology integrated into the MPS 200 is its flexibility in connectivity. It supports a variety of protocols, including SIP and H.323, ensuring compatibility with existing infrastructure. This flexible design allows organizations to integrate the MPS 200 into their current systems with minimal disruptions, making it an attractive option for businesses looking to upgrade their conferencing capabilities.

In addition to video conferencing, the MPS 200 offers features such as content sharing, which enables users to share documents, presentations, and other materials during meetings. This functionality enhances collaboration by allowing participants to view and discuss content in real-time, fostering engagement and ensuring that everyone remains on the same page.

The user interface of the MPS 200 is designed for ease of use, providing intuitive controls that facilitate quick setup and management of conferences. Users can initiate or join meetings with just a few clicks, ensuring that technology does not hinder productivity.

Security is a priority with the MPS 200, which incorporates various encryption methods to protect sensitive information during video calls. With security becoming increasingly important in today’s digital landscape, this feature offers peace of mind to users, particularly in enterprise environments.

In summary, the TANDBERG MPS 200 stands out as a comprehensive multipoint conferencing solution that delivers high-quality video, extensive connectivity options, and advanced collaboration features. Its user-friendly design, scalability, and robust security measures make it a vital asset for organizations aiming to enhance their communication strategies in the digital age. Whether for internal meetings or external engagements, the MPS 200 serves as an indispensable tool for effective collaboration.