Tandberg MPS at a Glance, Rack Mountable Chassis

Introduction

TANDBERG MPS at a Glance

TANDBERG MPS ADMINISTRATOR GUIDE

Rack Mountable Chassis

Front View

The TANDBERG MPS chassis is 19” rack-mount- able.

•On the front of the chassis is a Liquid Crystal Display (LCD) for initial configuration and basic system information.

•There are four Light Emitting Diodes (LEDs) indicating the power status.

•The backplane of the chassis is provided with advanced CompactPCI technology for high speed communication between the boards.

•There are three cooling fans in the lower front of the chassis.

•The TANDBERG MPS 800 has a 9U-19” rack-mountable chassis that can host up to 8 Media Processing Boards and up to 4 Network Interface Cards.

•The TANDBERG MPS 200 has 3U-19” rack- mountable chassis that can host up to 2 Me- dia Processing Boards and up to 2 Network Interface Cards.

System Controller Board

The System Controller Board is installed in the first slot in the chassis.

•In the MPS 800 the first slot is the first from the left of the chassis.

•In the MPS 200 the first slot is the first from the bottom of the chassis.

!Controller Board is installed in the first slot in the chassis! Installing inIt is very important that the System

any other slot can damage the System Con- troller Board.

The System Controller Board takes care of the following functions:

•Call control

•System management

•The embedded Web server

The System Controller Board is equipped with the following interfaces:

•1 X LAN / Ethernet (RJ-45) 10/100 Mbit on the front.

•2 X LAN / Ethernet (RJ-45) 10/100 Mbit on the back (only 1 in use, Enet2)

•1 x COM port on the front

•2 X USB port (these are for future use)

The LAN interface on the System Controller Board is for management/call control signal- ling. Note that management is disabled on Enet2. This interface is only for call control. The 2 LAN interfaces will allow you to con- nect to two non-overlapping IP-networks so that participants with no IP-routing between them can be joined in the same conference. At least one Media Processing Board must be connected to each network. The 2xLAN interfaces will give the TANDBERG MPS support for two Gatekeepers, one on each network. To use the COM1 port you need a RJ-45 to RS-232 converter. See the Techni- cal Description section for further details of the COM port pin out on the System Control- ler Board.

Media Processing Board

Add-on boards for media processing are installed in adjacent slots in the chassis. The Media Processing Boards handles the following functions:

•Video processing. See Video Features in the Tech- nical Descriptions section for details.

•Audio processing. See Audio > Create Conference in the Using the MPS section for details.

•Transcoding. See Transcoding and Ratematching in the Technical Descriptions section for details.

•Encryption. See Secure Conference (Encryption) in the Technical Descriptions section for details.

•Continuous Presence/Voice Switching. See Video Features in the Technical Descriptions section for details.

Each of the Media Processing Boards is equipped with 1xLAN interface for H.323 and SIP media. You will also find 4 Light Emitting Diodes (LEDs) for board status. With the TANDBERG MPS 800, there is sup- port for up to 8 Media Processing Boards. With the TANDBERG MPS 200, there is support for up to 2 Media Processing Boards. See the Technical Descrip- tion section for further details on the Media Process- ing Board.

The TANDBERG MPS 800 is shipped with 2 hot-swappable power units for configurations of 1 to 3 Media Processing Boards. If the unit has more than 3 Media Processing Boards the TANDBERG MPS 800 has to be equipped with

3hot-swappable power units. The power units are installed at the back of the chassis. You will also find the power switch/connector at the back of the chassis.

The TANDBERG MPS 200 is always shipped with 1 power unit integrated in the chassis.

System Controller Board - Rear View

The second LAN interface of the System Controller Board is accessible from the rear side.

See the Technical Description section for further details on the System Controller Board.

Rear View

Network Interface Cards

The Network Interface Cards of the TANDBERG MPS are installed from the rear panel.

There are two types of Network Interface Cards:

•PRI E1/T1 ISDN Interface Card (IIC-8).

Each PRI E1/T1 ISDN Interface Card has 8 x PRI interfaces.

•V.35 Serial Interface Card (SIC-32).

Each of the V.35 Serial Interface Card has 32 x V.35/RS366 ports.

There is support for up to 4 Network Interface Cards.

There can be a mix of PRI E1/T1 ISDN Interface Cards and V.35 Serial Interface Cards.

The PRI E1/T1 ISDN Interface Card and the V.35 Serial Interface Card may only be installed in slot 1-6. (1 being the first Media Processing Board, left from the System Controller Card, seen from the rear).

See the Technical Description section for further details of the different Network Interface Cards.

Main	Table of	Introduction
	Contents

D 13373.08

NOVEMBER 2007

Installation	Quick	Using	System	System	Gateway	MCU	Technical	Appendices
Installation	Setup	the MPS	Status	Configuration	Configuration	Configuration	Descriptions	Appendices
	Setup	the MPS	Status	Configuration	Configuration	Configuration	Descriptions
		18						MPS

MPS 800, MPS 200 specifications

The TANDBERG MPS 200 is an advanced multipoint conferencing solution designed to enhance communication and collaboration in various environments. Renowned for its robust performance and versatile features, the MPS 200 caters to businesses and organizations seeking to integrate video conferencing seamlessly into their operations.

One of the standout features of the MPS 200 is its ability to support high-definition video conferencing. Ensuring crystal-clear imagery, it accommodates various video standards, including H.264, allowing for efficient bandwidth usage without compromising quality. This makes it an excellent choice for organizations that require high-quality video for their meetings, presentations, or training sessions.

The MPS 200 also supports a wide range of participants, facilitating large-scale conferences with multiple endpoints. It can connect numerous participants simultaneously, allowing teams from different locations to collaborate effectively. This scalability is essential for businesses that frequently host meetings with various stakeholders, enabling seamless interaction and engagement.

Another noteworthy technology integrated into the MPS 200 is its flexibility in connectivity. It supports a variety of protocols, including SIP and H.323, ensuring compatibility with existing infrastructure. This flexible design allows organizations to integrate the MPS 200 into their current systems with minimal disruptions, making it an attractive option for businesses looking to upgrade their conferencing capabilities.

In addition to video conferencing, the MPS 200 offers features such as content sharing, which enables users to share documents, presentations, and other materials during meetings. This functionality enhances collaboration by allowing participants to view and discuss content in real-time, fostering engagement and ensuring that everyone remains on the same page.

The user interface of the MPS 200 is designed for ease of use, providing intuitive controls that facilitate quick setup and management of conferences. Users can initiate or join meetings with just a few clicks, ensuring that technology does not hinder productivity.

Security is a priority with the MPS 200, which incorporates various encryption methods to protect sensitive information during video calls. With security becoming increasingly important in today’s digital landscape, this feature offers peace of mind to users, particularly in enterprise environments.

In summary, the TANDBERG MPS 200 stands out as a comprehensive multipoint conferencing solution that delivers high-quality video, extensive connectivity options, and advanced collaboration features. Its user-friendly design, scalability, and robust security measures make it a vital asset for organizations aiming to enhance their communication strategies in the digital age. Whether for internal meetings or external engagements, the MPS 200 serves as an indispensable tool for effective collaboration.

TANDBERG MPS 200, MPS 800 Tandberg MPS at a Glance, Rack Mountable Chassis, Rear View, Front View

Models: MPS 800 MPS 200