Manuals / Tandberg Data / Kitchen Appliance / Refrigerator

Tandberg Data FS-1600, FS-1610 user manual RAID Management, Configure and Creation of RAID Volumes

Models: FS-1600 FS-1610

1 53

Download 53 pages 22.07 Kb

Page 35

5.2.RAID Management

Tandberg DataSystem Management

_____________________________________________________________

5.2.RAID Management

The RAID volume of FS-1600 Series NAS appliance is configured using the BIOS of ARECA ARC-1160 or ARC-1261ML Serial-ATA II RAID controller hardware. Additional or subsequent configuration can be performed using the web-based RAID manager once the OS is installed.

5.2.1.Configure and Creation of RAID Volumes

The RAID BIOS Configuration Utility is used to create or configure the hardware RAID of FS-1600 Series NAS appliance. After any modification of the hardware RAID, the appliance has to be rebooted in order for the changes to take effect.

Notes

The RAID BIOS is accessed by pressing TAB / F6 key during boot. The default BIOS password is “0000” when prompted.

Before restoring the factory default image to Viking FS-1600 Series NAS appliance, the System Volume (SV) on the hardware RAID controller must be created first. After the SV creation is finished, the appliance has to be rebooted to make the volume effective before the image restoration.

1.During the boot process, depress TAB / F6 key to enter the RAID BIOS.

2.Create RAID set that comprises of the physical member HDD. If you have 4 HDD, you can select all 4 HDD into a RAID set.

3.Create the Volume set (SV) within the RAID set. Decide the RAID level and strip size of SV and the desire capacity.

Notes

It is recommended that the minimum capacity of the System Volume is set to 10GB and RAID level 0+1 for OS redundancy. Tandberg Data does not recommend setting the capacity value of SV below 10GB.

4.Enter the default password word if prompted.

5.The system will start performing the RAID volume creation. Depending on the capacity of the SV selected as well as its RAID level, this process may take several hours to complete. Once completed, the appliance has to be rebooted for the volume to take effect.

5-3	Tandberg Viking FS-1600 Series NAS Hardware User Manual

Image 35

Tandberg Data FS-1600, FS-1610 RAID Management, Configure and Creation of RAID Volumes, Tandberg DataSystem Management

Contents

20 Bendemeer Road, #04-05 TANDBERG VIKING FS-1600 NAS APPLIANCEHardware User Manual TANDBERG DATA ASIATitle Part NoFront Panel LED Indicators Table of ContentsPackage Contents Features of Viking FS-1600Series NAS ApplianceTroubleshooting Steps Tandberg DataTable of ContentSystem Recovery Safety Guidelines1. Overview 1.1.Package Contents•Processor Tandberg DataOverviewTandberg DataOverview •Rear panel connectors5.LAN Access LED indicator 1.Power button2.Reset button 3.Power LEDTandberg DataOverview 1.4.Front Panel LED Indicators7.Power Supply Unit Failure LED 10.LAN connectors LAN1 & LAN2 2.Power supply connector6.USB connectors Connectors for USB devices 7.RS232 serial connectorTandberg DataOverview 1.6.Rear Panel LED Indicators LAN1.7.Storage 1.7.1.DVD-ROMDriveTandberg DataOverview 1.7.2.Hard Disk Drives2.1.Requirements 2. Setting Up2.1.1.Ambient Temperature 2.1.2.Height and Weight2.1.3.Rack Mounting 2.1.4.Power Source2.1.8.Battery Precaution Tandberg DataSetting UpDummy Drive Drive Tray Release Button 2.1.9.Sufficient VentilationTandberg DataSetting Up Hard Drive Hard Drive Tray Use a Hard, Stable Surface when installing the Hard DriveTandberg DataSetting Up Tandberg DataSetting Up 2.3Rack Installation: Content of Accessory KitTandberg DataSetting Up 2.4.Rack Mount InstallationInner Rack Rails Bracket Tandberg DataSetting UpOuter Rail Locking Tabs Tandberg DataSetting UpTandberg DataSetting Up 2.4.Connecting Cables2-10 2.6.TroubleshootingTandberg DataSetting Up Tandberg DataSetting Up 2-112-12 2.7.1.Using Microsoft WindowsTandberg DataSetting Up 3.1.Hardware RAID Layout 3. RAID ConfigurationRAID0 Tandberg DataRAID configuraionRAID1 System Volume Data Volume RAID5Tandberg DataRAID configuraion 3.2.RAID Volume Calculation3.1.1.System Volume SV 3.1.2.Data Volume DVTandberg DataRAID configuraion This Page Intentionally Left Blank4.2.Expanding Connectivity 4. Customizing the Viking FS1600 Series NAS Appliance 4.1.Preventing Static Electricity Discharge4.2.2.USB Connection 4.2.2.Removing/Installing Hot-SwapHard Drive4.3.Upgrading Storage Capacity 4.2.1.Built-inNetworkingTandberg Data Customizing the Viking FS-1600Series NAS Appliance This Page Intentionally Left Blank 5. System Management 5.1.Windows Installer•Intel Network driver Tandberg DataSystem ManagementTandberg DataSystem Management 5.2.1.Configure and Creation of RAID Volumes5.2.RAID Management Tandberg DataSystem Management 5.3.System Recovery5.2.2.Changing RAID Level and Capacity Size Tandberg DataSystem Management 4.Select Yes Local > Disk > From Image6. Select the GHOST Image listed Tandberg DataSystem Management8. Verify detail of the destination drive Tandberg DataSystem Management9. Click OK and the restoration will commence Tandberg DataSystem ManagementTandberg DataSystem Management This Page Intentionally Left Blank 5-10Tandberg DataSystem Management 6. Troubleshooting Tandberg DataTroubleshooting 6.2.Safety Guidelines6.3.Troubleshooting Steps •Make sure that the LINK LED and ACT LED are lit Tandberg DataTroubleshootingThis Page Intentionally Left Blank Tandberg DataTroubleshooting100 Base-TX DHCP Dynamic Host Configuration Protocol7. Glossary 10 Base-TLAN Local Area Network Tandberg DataGlossaryEvent Viewer IP addressNFS Network File System MountNetwork card Network system7-iv RAID 0+1Rack mount RouterServer ServiceVolume set Windows Administrative toolsTandberg DataGlossary 7-viThis Page Intentionally Left Blank 7-viiTandberg DataGlossary