Manuals / Taylor / Kitchen Appliance / Freezer

Taylor 342 manual Step, Models 340, 341, Operating Procedures

Models: 341 342 340

1 43

Download 43 pages 12.66 Kb

Page 15

Step 3

If the blades are in good condition, install the scraper blade clip over the scraper blade. Place the rear scraper blade over the rear holding pin (knife edge to the outside). Holding the blade on the beater, turn it over and install the front blade the same way.

Figure 6

Insert the torque rotor shaft, plastic bearing end first, making sure that it fits into the hole in the beater drive shaft. Rotate it several times to check for proper positioning. The hole in the torque rotor shaft should be in the 12 o’clock position.

Figure 4

Holding the blade in position, insert the beater assembly into the freezing cylinder and slide it into position over the drive shaft. Turn the beater slightly to be certain that the beater is properly seated. When in position, the beater will not protrude beyond the front of the freezing cylinder.

10362

Figure 5

Step 4

Install the torque rotor shaft. Slide the o-ring into the groove on the front of the shaft and lubricate these parts to prevent leaking. Place the white, plastic guide bearing on the rear of the rotor shaft. DO NOT lubricate the guide bearing.

Figure 7

Step 5

Assemble the freezer door with the “Ice Buster” (door spout clearing device). To assemble the door with the ice buster, install the o-rings on the draw valve and lubricate.

Figure 8

020807

Models 340, 341, 342	11	Operating Procedures

Image 15

Taylor 342 manual Step, Models 340, 341, Operating Procedures

Contents

028764-M Slush FreezersModels 340, 341 Operating InstructionsTaylor Company Complete this page for quick reference when service is requiredInformation found on the data label E January, 1997 Taylor All rights reserved 028764--MTable of Contents Models 340, 341 Table of ContentsAir Cooled Units To the InstallerSection Water Connections Water Cooled Units OnlyTo the Operator Compressor Warranty DisclaimerTo the Operator SectionTo Operate Safely SafetySafety SectionModels 340, 341 Section 4 Operator Parts IdentificationModel Operator Parts IdentificationDescription ModelModels 340, 341 Operator Parts IdentificationDescription ModelOperator Parts Identification Models 340, 341Description Models 340, 341, 342 Beater Door AssemblyModels 340, 341 Operator Parts IdentificationDescription AccessoriesOperator Parts Identification Models 340, 341Important To the Operator Symbol DefinitionsControl Switch Indicator Light - “Add Mix”Section Operating ProceduresAssembly Operating ProceduresStep Operating ProceduresStep StepOperating Procedures Insert the draw valve into the door, leaving approximately 1/2” of the valve sticking out the top of the doorModels 340 Step Operating ProceduresStep StepStep SanitizingStep Optional Rack Assembly Operating ProceduresStep PrimingOperating Procedures StepStep Closing ProcedureStep Optional Flavor Rack Assembly Operating ProceduresStep Draining Product From the Freezing CylinderRinsing Operating ProceduresStep CleaningOperating Procedures StepStep DisassemblyBrush Cleaning Operating ProceduresRegular Maintenance Checks Section 7 Important Operator ChecklistDuring Cleaning and Sanitizing Troubleshooting Bacterial CountWinter Storage Important Operator ChecklistModels 340, 341 Section Troubleshooting GuidePROBLEM Troubleshooting GuideREMEDY PROBLEMTroubleshooting Guide PROBABLE CAUSEREMEDY PROBLEMTroubleshooting Guide PROBABLE CAUSEEVERY Section 9 Parts Replacement ScheduleParts Replacement Schedule PART DESCRIPTIONModels 340, 341 Section Parts ListParts List UPDATEDESCRIPTION Parts ListUPDATE Models 340, 341DESCRIPTION Parts ListUPDATE Models 340, 341DESCRIPTION Parts ListUPDATE Models 340, 341DESCRIPTION Parts ListUPDATE Models 340, 341DESCRIPTION Parts ListUPDATE Models 340, 341Models 340/341 Rev. 3/06 Model 341 049359--33 Rev. 3/06 Model 340/341 049359--40 Rev. 3/06 Model 341 049359--58 Rev. 3/06 Model 342 052720--27 Rev. 3/06 Model 342 052720--33 Rev. 3/06 Model 342 052720--40 Rev. 3/06 Model 342 052720--58 Rev. 3/06