Teledyne 200A 8.6 Replacing the Molybdenum Converter

Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247

8.6 Replacing the Molybdenum Converter

The Molybdenum Converter is located in the center of the instrument, see Table 2-2-5 for

location, and Table 8-8-4 for the assembly. The heater, thermocouple, converter is designed to be

replaced as a single unit.

1. Turn off the power to the M200A and allow the converter to cool.

2. Remove the entire assembly from the chassis.

A. Remove the pneumatic fittings from the valves.

B. Remove the power to the valves, thermocouple wire and cartridge heater.

C. Remove the converter assembly from the chassis by loosening the 4 captive screws that

secure the assembly to the chassis.

CAUTION

The converter operates at 315º C. Severe burns can result

if not enough time is allowed for the assembly to cool. Do

not handle assembly until it is at room temperature.

3. Disconnect the gas fittings and power cable grounding from the can.

4. Remove the valve assembly and bottom bracket and re-attach those two parts to the

replacement moly assembly.

5. Re-attach the pneumatic fittings and valve assembly to the can.

6. Install the assembly back into the analyzer. Re-attach the electrical and pneumatic

fittings. Leak check the assembly when completed.

7. Turn the power back on. The insulation can emit a burnt odor for the first 24 hours, this is

normal. Allow the converter to burn-in for 24 hours, then re-calibrate the instrument.

8-7

PRINTED DOCUMENTS ARE UNCONTROLLED

Contents

Main INSTRUMENTS INSTRUCTION MANUAL Chemiluminescent NO/NO2/NOX ANALYZER Model 200A HIGHLIGHTS Page INSTRUCTION MANUAL MODEL 200A NITROGEN OXIDE ANALYZER Page SAFETY MESSAGES Page TABLE OF CONTENTS 3 SPECIFICATIONS, AGENCY APPROVALS, WARRANTY.............................. 3-1 6 OPTIONAL HARDWARE AND SOFTWARE....................................................... 6-1 7 CALIBRATION AND ZERO/SPAN CHECKS....................................................... 7-1 9 TROUBLESHOOTING, ADJUSTMENTS.............................................................. 9-1 Page Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 LIST OF FIGURES vii PRINTED DOCUMENTS ARE UNCONTROLLED Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 LIST OF TABLES Page Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 x PRINTED DOCUMENTS ARE UNCONTROLLED 1 HOW TO USE THIS MANUAL Page 2 GETTING STARTED 2.1 Unpacking 2.2 Electrical and Pneumatic Connections Page Page Page Page 2.3 Initial Operation Page Page Page Page Page Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 2-12 PRINTED DOCUMENTS ARE UNCONTROLLED Table 2-2-6: Final Test and Calibration Values (table continued) PROM # Serial # Date Technician 2-13 PRINTED DOCUMENTS ARE UNCONTROLLED Page Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 3 SPECIFICATIONS, AGENCY APPROVALS, WARRANTY 3.1 Specifications 3-1 PRINTED DOCUMENTS ARE UNCONTROLLED 3.2 EPA Equivalency Designation 3.3 Warranty Page 4 THE M200A NOX ANALYZER 4.1 Principle of Operation hv NO * NO Page 4.2 Operation Summary 4.2.1 Sensor Module, Reaction Cell, Detector 4.2.2 Pneumatic Sensor Board 4.2.3 Computer Hardware and Software 4.2.4 V/F Board 4.2.5 Front Panel Page 4.2.6 Power Supply Module 4.2.7 Pump, Valves, Pneumatic System Page Page 4.2.8 Ozone Generator 4.2.9 Molydbenum Converter Page 5 SOFTWARE FEATURES 5.1 Index To Front Panel Menus Page Page Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 5.1.1 Sample Menu Table 5-5-3: M200A Sample Menu Structure 9-1 5-4 PRINTED DOCUMENTS ARE UNCONTROLLED Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 5.1.2 Set-Up Menu Table 5-5-4: M200A Setup Menu Structure 5-5 PRINTED DOCUMENTS ARE UNCONTROLLED Table 5-5-6: M200A Menu Structure - Setup Menu #3 5-6 PRINTED DOCUMENTS ARE UNCONTROLLED Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 5-7 PRINTED DOCUMENTS ARE UNCONTROLLED 5.2 Sample Mode 5.2.1 Test Functions Page Page Page 5.2.2 CAL, CALS, CALZ, Calibration Functions Page 5.3 Set-Up Mode 5.3.1 Configuration Information (CFG) 5.3.2 Automatic Calibration (AutoCal) 5.3.3 Data Acquisition System (DAS) Page 5.3.4 Range Menu Page Page Page 5.3.5 Password Enable 5.3.6 Time of Day Clock 5.3.7 Diagnostic Mode 5.3.8 Communications Menu Page 5.4 Status Output 5.5 RS-232 Interface 5.5.1 Setting Up the RS-232 Interface Page Page Page 5.5.2 Command Summary 5-29 PRINTED DOCUMENTS ARE UNCONTROLLED Page Page Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 5.5.3 TEST Commands and Messages Table 5-5-17: RS-232 Test Messages 5-32 PRINTED DOCUMENTS ARE UNCONTROLLED 5.5.4 WARNING Commands and Messages 5.5.5 CALIBRATION Commands and Messages Page 5.5.6 DIAGNOSTIC Commands and Messages 5.5.7 DAS Commands and Message Page 5.5.8 Internal Variables Page 6 OPTIONAL HARDWARE AND SOFTWARE 6.1 Rack Mount Options 6.2 Zero/Span Valves Page 6.3 Internal Zero/Span (IZS) 6.4 Autocal - Setup of IZS and Zero/Span Valves Page 6.5 Permeation Tube Page Page 6.6 4-20 mA Current Loop Output 7 CALIBRATION AND ZERO/SPAN CHECKS 7-2 PRINTED DOCUMENTS ARE UNCONTROLLED Page 7.1 Manual Zero/Span Check or Cal With Zero/Span Gas in the Sample Port Page 7.2 Manual Zero/Span Check or Calibration with Zero/Span Valves Option 7.3 Manual Zero/Span Check with IZS Option 7.4 Automatic Zero/Span Check 7.5 Dynamic Zero/Span Calibration Page 7.6 Calibrate on NO2 Permeation Tube Page 7.7 Use of Zero/Span Valves or IZS with Remote Contact Closure 7.8 EPA Protocol Calibration 7.8.1 Calibration of Equipment Page 7.8.2 Calibration Gas and Zero Air Sources 7-14 PRINTED DOCUMENTS ARE UNCONTROLLED 7.8.3 Data Recording Device 7.8.4 Gas Phase Titration (GPT) System FT = analyzer flow demand (cm3/min) x 110/100 Equation 7-1 [NO]OUT = URL of analyzer (ppm) x 90/100 Equation 7-2 min2 FF V t Page min/ cm 24.5 ppm5.50 min/ cm 2750ppm45.0 = F = 80984 cm / - 24.5 cm / = 260 cm / 7.8.5 Dynamic Multipoint Calibration Procedure Page Page Page Page 7.8.6 Moly Converter Efficiency Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 7.8.6.1 Automatic Moly Converter Efficiency Compensation Table 7-7-17: Automatic Calculation of Converter Efficiency 7.8.7 Calibration Frequency 7.8.8 Other Quality Assurance Procedures Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 Table 7-7-18: Definition of Level 1 and Level 2 Zero and Span Checks (from Section 2.0.9 of Q.A. Handbook for Air Pollution Measurment Systems) 7.8.9 Summary of Quality Assurance Checks Table 7-7-19: Activity Matrix for Data Quality 7-29 PRINTED DOCUMENTS ARE UNCONTROLLED 7.8.10 ZERO and SPAN Checks 7.8.11 Recommended Standards for Establishing Traceability 7.8.12 Certification Procedures of Working Standards Page 7.9 Calibration of Independent Ranges or Autoranging 7.9.1 Zero Calibration with AutoRange or Independent Range 7.9.2 Span Calibration with AutoRange or Independent Range 7.10 Calibration Quality Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 Table 7-7-21: Calibration Quality Check After the above procedure is complete, the M200A is ready to measure sample gas. 7-36 PRINTED DOCUMENTS ARE UNCONTROLLED 7.11 References Page 8 MAINTENANCE 8.1 Maintenance Schedule Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 8-2 PRINTED DOCUMENTS ARE UNCONTROLLED Table 8-8-2: Preventative Maintenance Schedule 8.2 Replacing the Sample Particulate Filter Page 8.3 Replacing the Ozone Scrubber Charcoal 8.4 Replacing the Permeation 8.5 Replacing the IZS Zero Air Scrubber 8.6 Replacing the Molybdenum Converter Page 8.7 Cleaning the Reaction Cell Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 Table 8-8-5: Reaction Cell Assembly 8-10 PRINTED DOCUMENTS ARE UNCONTROLLED 8.8 Pneumatic Line Inspection Page Page Page 8.9 Leak Check Procedure 8.10 Light Leak Check Procedure 8.11 Prom Replacement Procedure 9 TROUBLESHOOTING, ADJUSTMENTS Page Page Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 Table 9-9-1: Test Functions Test Function Factory Set-Up Comment 9-4 PRINTED DOCUMENTS ARE UNCONTROLLED Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 Table 9-1: Test Functions (Continued) 9-5 PRINTED DOCUMENTS ARE UNCONTROLLED Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 Table 9-1: Test Functions (Continued) Test Function Factory Set-Up Comment 9-6 PRINTED DOCUMENTS ARE UNCONTROLLED Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 Table 9-1: Test Functions (Continued) Test Function Factory Set-Up Comment 9-7 PRINTED DOCUMENTS ARE UNCONTROLLED 9.1.2 Fault Diagnosis with WARNING Messages Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 Table 9-9-2: Front Panel Warning Messages 9-9 PRINTED DOCUMENTS ARE UNCONTROLLED Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 Table 9-2: Front Panel Warning Messages (Continued) 9-10 PRINTED DOCUMENTS ARE UNCONTROLLED 9.1.3 Fault Diagnosis Using DIAGNOSTIC Mode Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 Table 9-9-3: Summary of Diagnostic Modes 9-12 PRINTED DOCUMENTS ARE UNCONTROLLED Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 9.1.3.1 Signal I/O Diagnostic Table 9-9-4: Diagnostic Mode - Signal I/O 9-13 PRINTED DOCUMENTS ARE UNCONTROLLED Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 Table 9-4: Diagnostic Mode - Signal I/O (Continued) 9-14 PRINTED DOCUMENTS ARE UNCONTROLLED Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 Table 9-4: Diagnostic Mode - Signal I/O (Continued) 9-15 PRINTED DOCUMENTS ARE UNCONTROLLED Page Page 9.1.4 M200A Internal Variables Page Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 Table 9-9-5: Model 200A Internal Variables 9.1.5 Test Channel Analog Output 9-20 PRINTED DOCUMENTS ARE UNCONTROLLED Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 Table 9-9-6: Test Channel Readings 9-21 PRINTED DOCUMENTS ARE UNCONTROLLED Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 Table 9-6: Test Channel Readings (Continued) 9-22 PRINTED DOCUMENTS ARE UNCONTROLLED 9.1.6 Factory Calibration Procedure Page Page 9.2 Performance Problems 9.2.1 AC Power Check 9.2.2 Flow Check 9.2.3 No Response to Sample 9.2.4 Negative Output 9.2.5 Excessive Noise 9.2.6 Unstable Span 9.2.7 Unstable Zero 9.2.8 Inability to Span 9.2.9 Inability to Zero 9.2.10 Non-Linear Response 9.2.11 Slow Response 9.2.12 Analog Output Doesn't Agree with Display Concentration 9.3 Subsystem Troubleshooting and Adjustments 9.3.1 Computer, Display, Keyboard Page Page 9.3.2 RS-232 Communications Page Page 9.3.3 Voltage/Frequency (V/F) Board Page Page *Required settings Page Page 9.3.4 Status/Temp Board Page 9.3.5 Power Supply Module Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 Table 9-9-13: Power Supply Module Subassemblies 9-50 PRINTED DOCUMENTS ARE UNCONTROLLED Page Page Page 9.3.6 Ozone Generator Page Page 9.3.7 Flow/Pressure Sensor Page Page Page Page 9.3.8 NOx Sensor Module Page Page Page 9.3.9 Z/S Valves & IZS Permeation Tube Oven 9.3.10 Pneumatic System Page Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 10-1 PRINTED DOCUMENTS ARE UNCONTROLLED 10 M200A SPARE PARTS LIST Table 10-1: Teledyne API M200A Spare Parts List Part No. Description Includes: Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 10-2 PRINTED DOCUMENTS ARE UNCONTROLLED Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 10-3 PRINTED DOCUMENTS ARE UNCONTROLLED Page Page Page Page Page Teledyne API Model 200A NOX Analyzer Instruction Manual, 02246, Rev. G, DCN 5247 APPENDIX A ELECTRICAL SCHEMATICS Table A-1: Electrical Schematics A-1 PRINTED DOCUMENTS ARE UNCONTROLLED