7.Attaching an alternative anti$tip q Locate wall studs near the rear panel of the cavit and mark drill holes in the beam.device
|
|
|
|
|
|
|
|
|
|
|
|
| q | Predrill the | wooden | beam. |
|
|
|
|
| ||||
! |
| IMPORTANT | NOTE |
| ! |
|
|
|
|
|
|
| |||||||||||||
|
|
|
|
| q | Attach | the | wooden | beam to | the | rear | panel of the | |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| cavity. |
|
|
|
|
|
|
|
|
|
| |
If possible, always screw the wooden beam to |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
existing | studs on the | rear | panel | of the | cavity. |
| 8. | Preparing | to |
| connect | the water | |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||
If the antitip | brackets | cannot | be | attached |
| securely, |
| ||||||||||||||||||
|
| (only for | appliances | which | require | a | water | connection) | |||||||||||||||||
an alternative | antitip device | can | be attached. |
| See | also | •Connecting the | water". |
|
|
|
|
| ||||||||||||
However, ensure that there is no play between the |
|
|
|
|
|
| |||||||||||||||||||
appliance | and the antitip device. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
| 4"d |
|
| CAUTION |
|
| d |
|
| |||||||||||
q Saw | the wooden beam (cross section min. 3" x |
|
|
|
|
|
| ||||||||||||||||||
(75 | cmx | 100 cm)) | to | the | required length. |
| Turn off the main water tap to prevent damage |
|
| ||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||
Length is | equal to | the | width | of the installation |
| caused by leaking | water. |
|
|
|
|
|
| ||||||||||||
| cavity! |
|
|
|
|
|
|
|
|
|
|
i
-
-
Note |
|
|
|
|
|
| q | Attach the connecting pipe to the shutoff valve | ||
|
|
|
|
|
|
|
| according to the instructions supplied by the | ||
If the | installation cavity is | deeper | than | the | appliance,manufacturer of the | ice maker installation kit. | ||||
select | a | beam which has | a larger | cross section | or | Install the connecting | pipe. Always observe the | |||
attach | 2 | beams. |
|
|
|
| q | |||
|
|
|
|
| indicated gap dimensions to prevent damage to th | |||||
|
|
|
|
|
|
|
| |||
The beam must cover the | appliance by | at | least | 2" | connecting pipe when pushing in the appliance. | |||||
(50.8 | mm). |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
qAttach the connecting pipe to the floor with adhesive tape.
q Mark the installation | height | (lower edge of the beam) |
on the rear panel of | the | cavity. |
qSelect screws according to the thickness of the wooden beam: length = min. 2.5 x beam thickness, diameter #12 or #14.
i
Specify the number of screws according to the
cavity width, thereby ensuring that the beam can be attached securely.
18