Manuals / Tiger Products Co., Ltd / Lawn and Garden / Lawn Mower

Tiger Products Co., Ltd 6020009 manual Maintenance Greasing Spindle, Tightening Spindle Bolts

Models: 6020009

1 150

Download 150 pages 23.65 Kb

Page 78

Image 78

MAINTENANCE

GREASING SPINDLE

Locate grease fitting on inside of deck housing. Inject Tiger Spindle Lubricant, part number 06540000 into spindle housing. Fill with lubricant until lubricant weeps out of the top spindle seal. Lubricate spindle weekly or every 40 hours of use.

TIGHTENING SPINDLE BOLTS

The spindle mounting bolts should be checked and retorqued daily or every 10 hours of service. Torque the (6) bolts shown below to 331 ft. lbs.

Twin Rtry Maintenance Section 4-16

Page 78

Image 78

Tiger Products Co., Ltd 6020009 manual Maintenance Greasing Spindle, Tightening Spindle Bolts

Contents

PARTS LISTING WITH MOUNTING AND OPERATING INSTRUCTIONS Tiger Corporation3301 N. Louise Ave Sioux Falls, SD TWIN ROTARY ASSEMBLIESTO THE OWNER / OPERATOR / DEALER FORWARD Tiger CorporationPage This symbol means TABLE OF CONTENTSCAUTION - YOUR SAFETY IS AT RISK ASSEMBLY / MOUNTING SECTIONPage SAFETY SECTION SAFETYGeneral Safety Instructions and Practices Practice all usual and customary safe working precautions andSAFETY SAFETY LEA EL INSTRUCTIVODANGER DANGER DANGER DANGER SAFETYDANGER DANGER SG-10SAFETY sure you abide by the following rulesSG-20 SAFETYDANGER DANGER SG-23DANGER SAFETYDANGER DANGERDo not put hands or feet under mower decks. Blade Contact can result SAFETYDANGER DANGERSAFETY DANGERSTOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UN- LESS DANGER SAFETYDANGER DANGERSAFETY SEE YOURDEALER In addition to the design and configuration of this Implement, including Safety Signs and Safety Equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of the machine. Refer also to Safety Messages and operation instruction in each of the appropriate sections of the Tractor and Equipment Manuals. Pay close attention to the Safety Signs affixed to the Tractor and Equipment. SG-18SAFETY LOCATION 22839 MOWER DECK 22840 INSIDE OF CAB 24028 MOWER DECK10” x 5.5” MOWER DECK 18.25” x10” HYDRAULIC TANK SAFETY LOCATION 42350 MOWER DECK 33743 INSIDE OF CAB 42399 MOWER DECK42400 MOWER DECK SAFETY LOCATION 6T3217 MOWER DECK 6T3219 INSIDE OF CAB6T3220 FRONT PUMP MOUNT 6T3221 INSIDE OF CAB SAFETY LOCATION 6T3222 INSIDE OF CAB INSIDE OF CAB 6T3224 MOWER DECK6T3230 INSIDE OF CAB SAFETY LOCATION 6T3233 HYDRAULIC TANK 6T3234 INSIDE OF CAB6T3236 MOWER DECK HYDRAULIC TANK 6T3243 INSIDE OF CAB SAFETY LOCATION 6T3249A MOWER DECK 6T3261 MOWER DECK TB1011 MOWER DECKSAFETY 34852 HYDRAULIC TANKDESCRIPTION SAFETYDRILLING HOLES INTO UNKNOWN AREAS, wires and other parts may 50023This Act Seeks SAFETY FEDERAL LAWS AND REGULATIONSEmployer-Employee Operator Regulations DUTIESASSEMBLY SECTION Assembly SectionASSEMBLY TRACTOR PREPARATIONASSEMBLY ADJUSTING REAR WHEELS CRANKSHAFT ADAPTERCABLE CONTROL LEVER STAND ASSEMBLY LIFT VALVE MOUNT MAIN FRAME MOUNTINGSOLENOID BRAKE VALVE WEATHER-PACK/METRI-PACK ASSEMBLY ASSEMBLYASSEMBLY POLY-CARBONATE SAFETY WINDOW ASSEMBLY INSTALLING MIRROR BRACKET FRONT WORKLAMP RELOCATIONEXAUST SUPPORT BRACKET MUFFLER MUFFLER SHIELD MIRROR BRACKET ASSEMBLY EXHAUST MOUNT ASSEMBLY Picture # Picture #BEFORE WIRING ASSEMBLY SWITCH MOUNTINGHYDRAULIC TANK INSTALLATION AFTER WIRINGASSEMBLY Assembly SectionTEMPERATURE GAUGE MOUNTING GENERAL HOSE INSTALLATIONFRONT PUMP MOUNTING ASSEMBLYASSEMBLY INSTALLING O-RING FITTINGSSUB-FRAME AXLE BRACE MTG Installing straight, 45 degree and 90 degree O-ring fittings requires that the O- ring, washer and nut A be up against the swivel body B. Insert the swivel and turn in until the swivel is pointed in the right direction and the O-ring contact is made. Hold swivel in set direction with a wrench and turn the O-ring nut away from the swivel body and carefully tightenCABLE LIFT DRAFT BEAM INSTALLATION ASSEMBLYInstall ½” O-ring breather into butt port of inboard cylinder. In all fittings in the rod end of the cylinder according to diagrams in parts section. These fittings should be positioned to face the butt end of the cylinder ASSEMBLY DRAFT BEAM MOUNTING LIFT CONTROL FEEDLINESDECK / MOTOR FEEDLINE DECK MOUNTING AND LIFT ASSEMBLY ASSEMBLYCheck for oil leaks at all fittings and connections using a piece of paper or cardboard. DO NOT USE HANDS TO CHECK FOR FLUID LEAKS ASSEMBLY TURNBUCKLE ADJUSTMENT MOWER TESTINGFINAL PREPARATION FOR OPERATION ASSEMBLY COMBO LIFT DRAFT BEAM INSTALLATION DRAFT BEAM MOUNTINGAssembly Section ASSEMBLY DECK MOUNTING Check that all grease zerks have been installed in the draft beams pivot arm, left linkage arm, right linkage arm, and cylinder mounting earsDECK / MOTOR FEEDLINE 3-POINT DECK TILT CYLINDER ASSEMBLY DECK / MOTOR FEEDLINE MOUNTING contSTOP BOLT ADJUSTMENT CHECK FOR FLUID LEAKSASSEMBLY FINAL PREPARATION FOR OPERATION MOWER TESTINGASSEMBLY Assembly SectionOPERATION SECTION OPERATIONOPERATION Twion Rtry Operation SectionOPERATION STARTING TRACTOR AND MOWER OPERATION CONTROL LOCATION AND FUNCTIONS MOWER OPERATIONOPERATION Once on location, lower the mower deck slightly above the material to be cut, so the mower does not have to start under a load. Bring the R.P.M. of the tractor up to 1200 and engage the side mower. If a rear mower is being used, allow the R.P.M. to return to 1200 before engaging the rear mower2. Turn fan switch OFF center position, wait at least 3 seconds REVERSE FAN OPERATION1. Normal operating position is with fan switch ON upper position 3. Push switch DOWN to reverse 4. Allow chaff to clearOPERATION TRANSPORTING MOWER Transporting under the units own powerTransporting unit by flatbed trailer Next, switch the hose ends and reconnect to form two separate closed loops, see diagram below. Disconnect the lift cable from the head and secure the loose end back onto the cable with the cable clevis. Remove the keeper bolt and draft beam outer pivot pin. Separate the mower head from the tractor. Now reinstall the pivot pin and keeper bolts into the draft beam to prevent loss. OPEN THE BALL VALVES ON THE HYDRAULIC RESERVOIR BEFORE STARTING TRACTOR AGAIN! Serious damage will be caused if tractor is started with the ball valves closed OPERATIONINSPECTION SHEETS OPERATIONDO NOT OPERATE an UNSAFE TRACTOR or MOWER Rotary Mower PRE-OPERATION InspectionTractor ID# Make Date Shift OPERATIONTractor ID# Make Date Shift TRACTOR PRE-OPERATION InspectionOPERATION DO NOT OPERATE an UNSAFE TRACTOR or MOWERDO NOT OPERATE an UNSAFE TRACTOR or FRONT END LOADER FRONT END LOADER PRE-OPERATION InspectionMower ID# Make Date Shift OPERATIONTractor ID# Make Date Shift OPERATIONTRACTOR PRE-OPERATION Inspection DO NOT OPERATE an UNSAFE TRACTOR or FRONT END LOADEROPERATION Twion Rtry Operation SectionMAINTENANCE SECTION MAINTENANCEMAINTENANCE MAINTENANCE PRECAUTIONSBREAK IN PERIOD Tiger Mowers are designed for high performance and rugged durability, yet with simplified maintenance. The purpose of this section of the manual is to help the operator in the regular servicing of the mower. Regular maintenance at the intervals mentioned will result in the maximum efficiency and long life of the Tiger MowerSERVICE MAINTENANCE REGULAR MAINTENANCEDAILY OR EVERY 8 HOURS COMMENTSMONTHLY OR EVERY 150 HOURS MAINTENANCE WEEKLY OR EVERY 50 HOURSTROUBLESHOOTING YEARLY OR EVERY 500 HOURSCAUSE MAINTENANCESYMPTOMS REMEDYMAINTENANCE Motor will not workMAINTENANCE TORQUE SPECIFICATIONS General Specification LUBRICATION RECOMMENDATIONSMAINTENANCE DescriptionMAINTENANCE POLYCARBONATE CARE & MAINTENANCE CLEANING THE SUPERCOAT HARD-COATGRAFFITI REMOVAL MAINTENANCE DETAILED MAINTENANCERECOMMENDED FILLING INSTRUCTIONS FOR HYDRAULIC RESERVIORS REPLACEING IN-TANK HYDRAULIC FILTERMAINTENANCE DETAILED MAINTENANCE REPLACEING HIGH PRESSURE HYDRAULIC FILTER ELEMENTHEAD BOWL MAINTENANCE GREASING INNER AND OUTER DRAFT BEAM PIVOT POINTS GREASING THE UPPER AND LOWER SHEAVESTIGHTENING KNIFE BOLTS AND DISK BOLTS MAINTENANCE GREASING PUMP DRIVE SHAFT COUPLER DRIVE SHAFT YOKE, U-JOINT & STUB SHAFTMAINTENANCE ADJUSTING THE CABLE LIFT GREASING THE CASTER WHEEL SWIVELMAINTENANCE GREASING CASTER FRAME PIVOT POINTS BALL VALVESMAINTENANCE GREASING SPINDLE TIGHTENING SPINDLE BOLTSMAINTENANCE ROTARY KNIFE REPLACEMENTINSPECTION OF ROTARY KNIVES Failure to follow the following warnings and instructions may resultFailure to follow the following warnings and instructions may result REPLACEMENT OF ROTARY DISKMAINTENANCE serious injury or damage to the equipment or propertyMAINTENANCE HEAVY DUTY SPINDLE ASSEMBLY INSTALLATION AND BEARING ADJUSTMENTTHE SPINDLE ASSEMBLY MAINTENANCE BEARING INSTALLATION MAINTENANCE BEARING ADJUSTMENT MAINTENANCE DAILY MAINTENANCE SCHEDULE Maintenance SectionPARTS SECTION FORD TS 115-135A CAB, WOC, TWIN ROTARY3301 N. Louise Ave Sioux Falls, SD PARTS ORDERING GUIDETiger Corporation Direct any questions regarding parts toPARTS SECTION TABLE OF CONTENTS ASSEMBLYSECTION TRACTOR MOUNT KIT - MAIN FRAME Parts Section06700006 TRACTOR MOUNT KIT - MAIN FRAMEDESCRIPTION AVAILTRACTOR MOUNT KIT - HYDRAULICS, TRR Parts SectionMAIN FRAME - REFER TO MAIN FRAME PARTS TRACTOR MOUNT KIT - HYDRAULICS, TRRDESCRIPTION FRONT PUMP - REFER TO MAIN FRAME PARTSTRACTOR MOUNT KIT - HYDRAULICS, TRAILKAT Parts SectionMAIN FRAME - REFER TO MAIN FRAME PARTS TRACTOR MOUNT KIT - HYDRAULICS, TRAILKATDESCRIPTION FRONT PUMP - REFER TO MAIN FRAME PARTSTRACTOR MOUNT KIT - BRACE/BATT, CAB/WOC Parts SectionTRACTOR MOUNT KIT - BRACE/BATT, CAB/WOC DESCRIPTIONMAIN FRAME - REFER TO MAIN FRAME PARTS CABLE LIFT VALVE - 2SP, CAB/WOC Parts SectionCABLE LIFT VALVE - 2SP, CAB/WOC DESCRIPTIONCOMBO LIFT VALVE - 2SP, CAB/WOC Parts SectionCOMBO LIFT VALVE - 2SP, CAB/WOC DESCRIPTIONCABLE LIFT VALVE - 3SP, CAB/WOC Parts SectionCABLE LIFT VALVE - 3SP, CAB/WOC DESCRIPTIONCOMBO LIFT VALVE - 3SP, CAB/WOC Parts SectionCOMBO LIFT VALVE - 3SP, CAB/WOC DESCRIPTIONMIRROR BRACKET Parts SectionMIRROR BRACKET DESCRIPTIONCOLLAR,CLAMP,EXHAUST,TS115A HYDRAULIC COOLER ASSEMBLY, CAB Parts Section06510029 HYDRAULIC COOLER ASSEMBLY, CABDESCRIPTION AVAILBOOM POLYCARBONATE CAB SAFETY WINDOW KIT DESCRIPTIONPOLYCARBONATE, NHTSA 115, DOOR, RH NON-CAB STEEL CANOPY - OPTIONAL U-BOLT,3.25x5.00x.50,20NF,GR8DESCRIPTION EXHAUST MOUNT DESCRIPTIONTUBE,EXHAUST RELOCATE,TSA,6CYL OPTIONAL PUMP AND GRILL GUARD KIT DESCRIPTIONBRAKE VALVE SOLENOID DESCRIPTION06510027 SOLENOID VALVE SWITCH AND WIRINGDESCRIPTION AVAILParts Section COMMON PARTS SECTION TWIN ROTARY COMMON SECTIONSECTION TABLE OF CONTENTSASSEMBLY PAGEPARTS ORDERING GUIDE Tiger Corporation3301 N. Louise Ave Sioux Falls, SD REAR ROTARY DECK ASSEMBLY Twin Rotary Common Section06504011 REAR ROTARY DECK ASSEMBLYDESCRIPTION CURRENT MOTOR, M365 - 2 GEARTRAILKAT REAR ROTARY DECK ASSY NOTE ORIENTATION OF ITEM 34, LARGE ZERK FORWARDTRAILKAT REAR ROTARY DECK ASSY 06320002REAR ROTARY CASTER WHEEL & 3PT ASSEMBLY Twin Rotary Common SectionNOT SHOWN REAR ROTARY CASTER WHEEL & 3PT ASSEMBLYDESCRIPTION BEARING, CONE, CASTER WHEELREAR ROTARY HYDRAULICS Twin Rotary Common SectionRTRY, 60” CPLT - HP W/FBAR TRR REAR ROTARY HYDRAULICSDESCRIPTION VALVE,BRAKE,SOL,3000PSI,METRI60” ROTARY MOTOR Twin Rotary Common SectionDESCRIPTION MOTOR ASSEMBLY 2 1/4” COMPLETE TRB6060” ROTARY MOTOR 06504016PUMP - SERVICE PARTS Twin Rotary Common SectionPUMP - SERVICE PARTS DESCRIPTION2 SP HUSCO - LOAD SENSE Twin Rotary Common Section2 SP HUSCO - LOAD SENSE DESCRIPTION2 SP HUSCO - LOAD SENSE Twin Rotary Common Section2 SP HUSCO - LOAD SENSE DESCRIPTION3 SP HUSCO - LOAD SENSE CABLE Twin Rotary Common Section3 SP HUSCO - LOAD SENSE CABLE DESCRIPTION3 SP HUSCO - LOAD SENSE COMBO Twin Rotary Common Section3 SP HUSCO - LOAD SENSE COMBO DESCRIPTIONSIDE COOLER Twin Rotary Common SectionSIDE COOLER DESCRIPTIONSAFETY STAND DESCRIPTIONCASTER WHEEL ASSEMBLY DESCRIPTIONRIM, OUTER/RR RTRY CASTER ASSY BRAKE VALVE ASSEMBLY W/ METRI PAK DESCRIPTIONSWITCHBOX SERVICE PARTS SWITCHBOX SCHEMATIC Twin Rotary Common SectionWARRANTY SECTION Warranty SectionPage WARRANTY INFORMATION THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THOSE EXPRESSED HEREINONE LAST WORD SAFETY IS YOUTO THE OWNER / OPERATOR / DEALER OWNER REQUIREMENTSOPERATOR REQUIREMENTS Printed in USA Tiger Corporation