APPENDIX 1 MESSAGES AND LEDS
ENGLISH VERSION
APPENDIX 1 MESSAGES AND LEDS
APPENDIX 1 MESSAGES AND LEDS
Appendix 1 describes the LCD messages displayed on the operation panel.
Symbols in the message
1:: The LED is illuminated. ~: The LED is flashing. z: The LED is unlit.
2:****: the number of unprinted media. Up to 9999 (in pieces)
3:%%%%%%%: ATA Card’s remaining memory 0 to 9999999 (in K bytes)
4:###: Flash memory card remaining memory for PC save area: 0 to 895 (in K bytes)
5:&&&&: Remaining flash memory capacity for storing writable characters 0 to 3147 (in K bytes)
|
| LED Indication |
| Restoration by | Acceptance of |
No. | LCD Message |
| Printer Status | RESTART key | Status Request |
| |||||
|
| POWER ONLINE ERROR |
| Yes/No | Reset Command |
|
|
| Yes/No |
1 | ON LINE |
| | | z | In online mode | Yes | |
ON LINE |
| | ~ | z | In online mode (The printer in | Yes | ||
|
| communication) |
|
| ||||
2 | HEAD OPEN |
| | z | z | The print head block is opened in online | Yes | |
| mode. |
|
| |||||
3 | PAUSE **** |
| | z | z | The printer is paused. | Yes | Yes |
|
|
|
|
|
| A parity, overrun, or framing error has | Yes | Yes |
4 | COMMS ERROR | | z | | occurred during communication through |
|
| |
|
|
|
|
|
| the |
|
|
5 | PAPER JAM | **** | | z | | The media is jammed during paper feed. | Yes | Yes |
6 | CUTTER ERROR**** | | z | | A problem has occurred with the cutter | Yes | Yes | |
module. |
|
| ||||||
7 | NO PAPER | **** | | z | | The media has run out, or the media is | Yes | Yes |
not loaded properly. |
|
| ||||||
8 | NO RIBBON | **** | | z | | The ribbon has run out. | Yes | Yes |
9 | HEAD OPEN | **** | | z | | Feed or printing was attempted with the | Yes | Yes |
print head block open. |
|
| ||||||
10 | HEAD ERROR | | z | | There is a problem with the print head. | Yes | Yes | |
11 | EXCESS HEAD TEMP | | z | | The print head is overheated. | No | Yes | |
|
|
|
|
|
| The ribbon has been torn. A problem | Yes | Yes |
12 | RIBBON ERROR**** | | z | | has occurred with the sensor that |
|
| |
determines the torque for the ribbon |
|
| ||||||
|
|
|
|
|
| motor. |
|
|
13 | REWIND FULL **** | | z | | An overflow error has occurred in the | Yes | Yes | |
rewinder unit. |
|
| ||||||
| SAVING%%%%%%% |
|
|
| In writable character or PC command | Yes | ||
14 | or |
| | | z | save mode |
|
|
| SAVING ###&&&& |
|
|
|
|
|
| |
15 | FLASH WRITE ERR. | | z | | An error has occurred while writing to | No | Yes | |
flash memory or ATA card. |
|
| ||||||
|
|
|
|
|
| An erase error has occurred in | No | Yes |
16 | FORMAT ERROR | | z | | formatting the flash memory or ATA |
|
| |
|
|
|
|
|
| card. |
|
|
17 | FLASH CARD FULL | | z | | Data cannot be stored because the flash | No | Yes | |
memory or ATA card is full. |
|
| ||||||
18 | Display of error | | z | | A command error has occurred in | Yes | Yes | |
| message (See Notes.) |
|
|
| analyzing the command. |
|
| |
19 | POWER FAILURE | | z | | A power failure has occurred. | No | No | |
20 | INTIALIZING… | | z | z | A flash memory card is being initialised. | |||
21 | EEPROM ERROR | | z | | Data cannot be read from/written to a | |||
|
|
|
|
|
| backup EEPROM properly |
|
|
EA1- 1
