Manuals / Toshiba / Computer Equipment / Printer

Toshiba BSX5TTS22QMR, BSX5TTS25QMR manual Strip Wait Status Selection, Feed Key Function Selection

Models: BSX5TTS25QMR B-SX5T-TS25-QM-R B-SX5T-TS22-QM-R BSX5TTS22QMR

1 120

Download 120 pages 3.28 Kb

Page 38

2. PRINTER SETUP

ENGLISH VERSION EO1-33059

2.9 Setting an Operating Environment

2.9.1Parameter Setting (Cont.)

(14) Strip Wait Status Selection

This parameter is to choose when the printer sends a strip wait status (05H) to a host in response to a status request command.

When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears.

<2>PARAMETER SET PEEL OFF STS OFF

Use the [FEED] or [RESTART] key to select a desired option.

PEEL OFF STS OFF

[RESTART]

[FEED]

A strip wait status is sent when the printer receives the next issue command and the previously printed label is waiting to be removed.

PEEL OFF STS ON

A strip wait status is sent when a printed label is waiting to be removed.

After selecting the Strip Wait Status, press the [PAUSE] key.

(15) FEED Key Function Selection

This parameter is to choose the function of the [FEED] key.

When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears.

<2>PARAMETER SET FEED KEY FEED

Use the [FEED] or [RESTART] key to select a desired option.

[RESTART]

[FEED]

FEED KEY FEED

The [FEED] key will feed one media when pressed.

FEED KEY PRINT

The [FEED] key will print the data in the Image Buffer (The last printed data)

After selecting the FEED key function, press the [PAUSE] key.

E2-24

Image 38

Toshiba BSX5TTS22QMR, BSX5TTS25QMR, B-SX5T-TS22-QM-R manual Strip Wait Status Selection, Feed Key Function Selection

Contents

SX5T Series CE Compliance for EU only Vorsicht SX5T Series Waste Recycling information for users For all countries and areas Safety Summary Meanings of Each Symbol Precautions Request Regarding Maintenance Table of Contents E7-1 E5-1E6-1 EA1-1 Introduction Features Unpacking Product Overview Accessories Contents Rear View DimensionsFront View Operation Panel Interior Options Option Name Type Usage Procedure Printer SetupSetup Flow Reference Installation Example of US Type Connecting the Power CordFitting the Fan Filter Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position STANDARD/PEEL OFF position Batch modeStrip mode Built-in rewinder mode Adjustment Cut mode Option Loading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning the Printer Turning on the Printer Pcmcia Cards How to enter the System Mode Parameter Setting Sequentially Character Code Selection Character Zero Selection Baud Rate Selection Data Length Selection Flow Control Code Selection Stop Bit SelectionParity Selection LCD Language Selection Auto Forward Wait Selection Head Up Cut/Rewinder Selection Feed key Solenoid Type Selection Ribbon Saving Function Selection Control Code Selection Strip Wait Status Selection Feed Key Function Selection Kanji Code Selection Euro Code Selection Auto Print Head Check Selection Centronics Interface ACK/BUSY Timing Selection Web Printer Function Selection Input Prime Selection Ribbon Near End Selection Expansion I/O Interface Type Selection Centronics Interface Selection Plug & Play Selection Label End/Ribbon End Selection Pre-Strip Selection Maxi Code Specification Selection Reverse Feed Speed Selection Print Head Type Selection Dump Mode Setting Dumped Receive Buffer Size Required Label Length When the Pause key is pressed, Basic program is executed General Description Installing the Printer DriversIntroduction Installing the Printer Driver Parallel Interface Windows 98/Me E2-39 Windows 2000/XP E2-41 USB Interface E2-43 E2-44 E2-45 Finish button E2-47 E2-48 E2-49 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/ME Deleting a LAN Port Printer Driver Upgrades Others Using the Printer Driver Adjustment Print Test When using a Strip Module or an optional Cutter Module Cut/Strip Position Fine Adjustment Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Coordinate Fine Adjustment Position and Print Tone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm Position and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Feed and Pause keys „ When using the Black Mark Sensor „ When using the Feed Gap Sensor „ Manual Threshold Setting „ Storing a No Media Level Voltage THRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V On Line Mode Operation Panel Reset Operation Print Head/Platen/ Sensors MaintenanceCleaning Covers and Panels Optional Cutter Module Error Messages Problems/Causes Solutions TroubleshootingError Messages Restart key Error Messages Problems/Cause Solutions Possible Problems Possible Problems Causes Solutions Refer to .1 Media Removing Jammed Media Printer Specifications Model SX5T-TS22-QM-R Media Type Supply SpecificationsMedia Label Tag paper with square holes Detection Area of the Transmissive SensorLabel Detection Area of the Reflective Sensor Effective Print Area „ B-9704-RFID-H1-QM-R Rfid Tags„ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R Media feed direction Media type Description RibbonRecommended Media and Ribbon Types Combination of Media and Ribbon Care/Handling of Media and RibbonRibbon type Description Symbols in the message Appendix 1 Messages and Leds System Error Following message appears Appendix 2 Interface Parallel interface Centronics Standard Connector Serial interface Standard LAN Option B-9700-LAN-QM-R Expansion I/O Interface Option B-7704-IO- QM-R RFID-H1-QM RFID-U1-USRFID-U1-EU Appendix 3 Power Cord When purchasing the power cord Appendix 4 Print Samples EAN13+2 digits Interleaved 2JAN13, EAN13 EAN13+5 digits Customer bar code UPC-A+5 digitsIndustrial 2 KIX Code Appendix 5 Glossaries Bar code Print head element USB Universal Serial Bus Power LED Index Index EO1-33059