Manuals / Toshiba / Computer Equipment / Printer

Toshiba B-SX5T-TS25-QM-R, BSX5TTS25QMR manual Printer Setup, Setup Flow, Procedure, Reference

Models: BSX5TTS25QMR B-SX5T-TS25-QM-R B-SX5T-TS22-QM-R BSX5TTS22QMR

1 120

Download 120 pages 3.28 Kb

Page 15

2. PRINTER SETUP

ENGLISH VERSION EO1-33059

2. PRINTER SETUP

2. PRINTER SETUP

This section outlines the procedures to setup your printer prior to its operation. The section includes precautions, loading media and ribbon, connecting cables, setting the operating environment of the printer, and performing an online print test.

Setup Flow

Installation

Fitting the fan filter

Connecting the power cord

Loading the media

Media sensor position

alignment

Loading the ribbon

Connecting to a host computer

Turning the power ON

Setting the operating

environment

Installing the printer driver

Print test

Position and Print Tone Fine

adjustment

Automatic threshold setting

Manual threshold setting

Procedure

After referring to the Safety Precautions in this manual, install the printer on a safe and stable location.

Fit the supplied fan filter to the ventilation of the printer.

Connect a power cord to the power inlet of the printer, then, to an AC outlet.

Load a label stock or tag stock.

Adjust the position of feed gap sensor or black mark sensor according to the media to be used.

In case of thermal transfer printing, load the ribbon.

Connect the printer to a host computer or a network.

Turn on the printer power.

Set the printer parameters in the system mode.

If necessary, install the printer driver in your host computer.

Make a print test in your operating environment and check the print result.

If necessary, fine adjust the print start position, cut/strip position, print tone, etc.

If the print start position cannot be detected properly when pre-printed label is used, set the threshold automatically.

If the print start position cannot be detected properly even an automatic threshold setting is performing, manually set the threshold.

Reference

2.1Installation

2.2Fitting the Fan Filter

2.3Connecting the Power Cord

2.4Loading the Media

2.4Loading the Media

2.5Loading the Ribbon

2.6Connecting the Cables to Your Printer

2.7Turning the Printer

ON/OFF

2.9Setting an Operating Environment

2.10Installing the Printer Drivers

2.11Print Test

2.12Position and Print Tone Fine Adjustment

2.13Threshold Setting

2.13Threshold Setting

E2- 1

Image 15

Toshiba B-SX5T-TS25-QM-R, BSX5TTS25QMR, B-SX5T-TS22-QM-R, BSX5TTS22QMR manual Printer Setup, Setup Flow, Procedure, Reference

Contents

SX5T Series Vorsicht CE Compliance for EU only SX5T Series Waste Recycling information for users For all countries and areas Meanings of Each Symbol Safety Summary Request Regarding Maintenance Precautions Table of Contents EA1-1 E5-1E6-1 E7-1 Product Overview Introduction Features Unpacking Contents Accessories Dimensions Front ViewRear View Interior Operation Panel Option Name Type Usage Options Reference Printer SetupSetup Flow Procedure Installation Connecting the Power Cord Fitting the Fan FilterExample of US Type Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position Batch mode Strip modeSTANDARD/PEEL OFF position Adjustment Built-in rewinder mode Cut mode Option Loading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning on the Printer Turning the Printer Pcmcia Cards How to enter the System Mode Sequentially Parameter Setting Character Zero Selection Character Code Selection Data Length Selection Baud Rate Selection Stop Bit Selection Parity SelectionFlow Control Code Selection Auto Forward Wait Selection LCD Language Selection Feed key Head Up Cut/Rewinder Selection Ribbon Saving Function Selection Solenoid Type Selection Control Code Selection Feed Key Function Selection Strip Wait Status Selection Euro Code Selection Kanji Code Selection Centronics Interface ACK/BUSY Timing Selection Auto Print Head Check Selection Input Prime Selection Web Printer Function Selection Expansion I/O Interface Type Selection Ribbon Near End Selection Plug & Play Selection Centronics Interface Selection Pre-Strip Selection Label End/Ribbon End Selection Reverse Feed Speed Selection Maxi Code Specification Selection Print Head Type Selection Dumped Dump Mode Setting Required Label Length Receive Buffer Size When the Pause key is pressed, Basic program is executed Installing the Printer Drivers IntroductionGeneral Description Parallel Interface Installing the Printer Driver Windows 98/Me E2-39 Windows 2000/XP E2-41 USB Interface E2-43 E2-44 E2-45 Finish button E2-47 E2-48 E2-49 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN Port Deleting a LAN Port Others Printer Driver Upgrades Using the Printer Driver Print Test Adjustment When using a Strip Module or an optional Cutter Module Coordinate Fine Adjustment Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Cut/Strip Position Fine Adjustment Tone Fine Position and Print Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm Position and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Feed and Pause keys „ When using the Feed Gap Sensor „ When using the Black Mark Sensor „ Storing a No Media Level Voltage „ Manual Threshold Setting THRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V Operation Panel On Line Mode Operation Reset Maintenance CleaningPrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Restart key TroubleshootingError Messages Error Messages Problems/Causes Solutions Error Messages Problems/Cause Solutions Possible Problems Causes Solutions Possible Problems Refer to .1 Media Removing Jammed Media Model Printer Specifications SX5T-TS22-QM-R Label Supply SpecificationsMedia Media Type Detection Area of the Transmissive Sensor LabelTag paper with square holes Effective Print Area Detection Area of the Reflective Sensor Rfid Tags „ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R„ B-9704-RFID-H1-QM-R Media feed direction Ribbon Recommended Media and Ribbon TypesMedia type Description Care/Handling of Media and Ribbon Ribbon type DescriptionCombination of Media and Ribbon Appendix 1 Messages and Leds Symbols in the message System Error Following message appears Parallel interface Centronics Standard Appendix 2 Interface Connector Serial interface Standard LAN Option B-9700-LAN-QM-R Expansion I/O Interface Option B-7704-IO- QM-R RFID-U1-US RFID-U1-EURFID-H1-QM When purchasing the power cord Appendix 3 Power Cord Appendix 4 Print Samples EAN13+5 digits Interleaved 2JAN13, EAN13 EAN13+2 digits KIX Code UPC-A+5 digitsIndustrial 2 Customer bar code Bar code Appendix 5 Glossaries USB Universal Serial Bus Print head element Index Power LED Index EO1-33059