Manuals / Toshiba / Household Appliance / Home Security System

Toshiba ESV41T Reset the NVR to Factory Default, ESV4 User’s Manual, Power-offthe device

Models: ESV41T

1 175

Download 175 pages 43.21 Kb

Page 115

Reset the NVR to Factory Default

ESV4 User’s Manual 115

Reset the NVR to Factory Default

To reset the recorder back to its factory default, click “Restore Factory Default” button and begin the process.

The process should be displayed and you should be prompted back to the “Live View” page after it is complete.

To perform hardware reset to default, follow the instructions below:

-Power-off the device

-Press and Hold reset button at the back of the device.

-Power-on the device

-Wait till all the LED’s are solid green.

-Release the reset button

Image 115

Toshiba ESV41T user manual Reset the NVR to Factory Default, ESV4 User’s Manual, Power-offthe device, Power-onthe device

Contents

4CH Network Video Recorder with Local Display ESV4 User’s ManualVersion Table of Contents 2ESV4 User’s ManualESV4 User’s Manual NVR Setup --System Options Web Interface4ESV4 User’s Manual Front View System OverviewESV4 User’s Manual Rear View 6ESV4 User’s ManualAudio Line- out NTSC Part namesLED Definition ESV4 User’s ManualHDD Installation Installation8ESV4 User’s Manual Slide open the case as shown above ESV4 User’s ManualMake sure the HDD is securely attached 10ESV4 User’s ManualPlace the HDD to the tray and make sure the screw holes on the HDD are aligned with the ones on the tray ESV4 User’s Manual12ESV4 User’s Manual Use Device Search Utility Connect to the NVRESV4 User’s Manual 14ESV4 User’s Manual ESV4 User’s Manual Once the installation is complete, check the “Launch the Search AP” option and click “Finish”16ESV4 User’s Manual ESV4 User’s Manual Access the NVR with its default IP address18ESV4 User’s Manual Set up PasswordAdd a Camera --Automatic Search Camera InstallationESV4 User’s Manual 20ESV4 User’s Manual ESV4 User’s Manual Add a camera manuallyRetrieve camera’s video stream Live View Web InterfaceLive View 22ESV4 User’s ManualBlue Connected Gray Disconnected Retrieve camera’s statusPerform Sequence Viewing ESV4 User’s Manual24ESV4 User’s Manual ESV4 User’s Manual PTZ Control26ESV4 User’s Manual Perform PTZ Preset ViewingAuto Pan Viewing Preset Point ViewingESV4 User’s Manual 28ESV4 User’s Manual Preset Point Sequence ViewingLive Video Controls Take a snapshot of a live video Display ratio and full screenESV4 User’s Manual The new window displays the snapshot 30ESV4 User’s ManualESV4 User’s Manual 32ESV4 User’s Manual ESV4 User’s Manual Perform Digital PTZ34ESV4 User’s Manual ESV4 User’s Manual Adjust Brightness for the Live Video36ESV4 User’s Manual Adjust Contrast for the Live VideoESV4 User’s Manual Change Web UI Display LanguageLive View through iPhone Safari Browser 38ESV4 User’s ManualType in the IP address of the NVR in the address bar ESV4 User’s Manual40ESV4 User’s Manual ESV4 User’s Manual Live View through Blackberry Phones42ESV4 User’s Manual ESV4 User’s Manual Press the menu button and click the “Save Options” to save settings44ESV4 User’s Manual ESV4 User’s Manual Playback Web InterfacePlayback Methods to Search Playback Videos46ESV4 User’s Manual Search by time chartESV4 User’s Manual Search by event48ESV4 User’s Manual ESV4 User’s Manual Play by specific timeSearch by event Most Recent 50ESV4 User’s Manual1.Play Audio 2.Snapshot 3.Export as AVI file 4.Digital PTZ 5.Adjust Brightness6.Adjust Contrast ESV4 User’s ManualTake a snapshot of a playback video 52ESV4 User’s ManualThe new window displays the snapshot ESV4 User’s Manual54ESV4 User’s Manual ESV4 User’s Manual 56ESV4 User’s Manual Adjust Brightness for the Playback VideoExport Playback Videos to AVI Files Adjust Contrast for the Playback VideoESV4 User’s Manual 58ESV4 User’s Manual ESV4 User’s Manual 60ESV4 User’s Manual Click “Open” >> “AVI File” ESV4 User’s ManualThe video will then start playing 62ESV4 User’s ManualESV4 User’s Manual NVR Setup --System Configurations Web InterfaceNetwork Setup Open Event Snapshot images with NVR Media Player64ESV4 User’s Manual Network SettingsESV4 User’s Manual DHCP Server66ESV4 User’s Manual DDNS ServiceESV4 User’s Manual 68ESV4 User’s Manual Fill in the necessary fields as illustrated above ESV4 User’s Manual70ESV4 User’s Manual ESV4 User’s Manual Go back to the NVR’s DDNS service configuration page under “Setup” >> “System Configuration” >> “DDNS Service”72ESV4 User’s Manual Time and DateESV4 User’s Manual User AccountAdd a new user 74ESV4 User’s ManualESV4 User’s Manual Change the password of the “admin” account76ESV4 User’s Manual Group PrivilegeYou can change the group name by clicking the “Change Group Name” button. A text box will be displayed for you to enter the new group ESV4 User’s Manual78ESV4 User’s Manual Disk SetupESV4 User’s Manual NVR Setup --Channel Configurations Web InterfaceAdd a camera Automatic Search80ESV4 User’s Manual Click “Add” to finish adding the camera ESV4 User’s Manual82ESV4 User’s Manual You will be able to use different video format for continuous recording if its a multi-streamcapable camera ESV4 User’s ManualAdd a camera manually 84ESV4 User’s ManualESV4 User’s Manual OSD Settings86ESV4 User’s Manual PTZ Preset Settings PTZ SettingESV4 User’s Manual 88ESV4 User’s Manual PTZ Preset SequenceESV4 User’s Manual To configure preset sequence for a cameraLocal Map Setting E-MapSetting90ESV4 User’s Manual To replace the map, click “Browse” button to locate the new map image file from the local PC and then click “Upload” ESV4 User’s Manual92ESV4 User’s Manual Google Map SettingESV4 User’s Manual 1.Zoom in to a smaller area by using the zoom control bar on the mapEvent Configuration NVR Setup --Event Configurations Web Interface94ESV4 User’s Manual How often an event is triggered General SettingsDefine when an event will be triggered ESV4 User’s Manual96ESV4 User’s Manual ESV4 User’s Manual DI SettingsEvent Servers Configuring an FTP server98ESV4 User’s Manual To add an FTP server ESV4 User’s Manual100ESV4 User’s Manual Configuring an SMTP serverESV4 User’s Manual Event Triggers102ESV4 User’s Manual General SettingsYou can define the following in “General Settings” General SettingsESV4 User’s Manual 104ESV4 User’s Manual ESV4 User’s Manual The HDD space recycle function is turned on by default. You can alternatively turn it off and set a system event in NVR Setup>>Event Configurations>>Event Trigger>>Event Handling Settings>>When NVR is triggered by, and set a desired disk remaining space for event trigger condition. Youd have to take action manually after you get the system event notification, such as replacing disk, turn on HDD recycle function, or backup recording data106ESV4 User’s Manual Schedule Recording To configure a schedule recordingESV4 User’s Manual Device Information NVR Setup --System Options Web Interface108ESV4 User’s Manual ESV4 User’s Manual Device Information110ESV4 User’s Manual Logs and Reports•Reboot cameras directly from the NVR Maintenance“Maintenance” provides functions for users to •Reboot the NVR when necessaryThrough the web interface Reboot the NVR at a specific time automaticallyFirmware Upgrade 112ESV4 User’s ManualESV4 User’s Manual When done, click “Upgrade”114ESV4 User’s Manual Upgrade through USB thumb driveRelease the reset button Reset the NVR to Factory DefaultPower-offthe device Power-onthe device116ESV4 User’s Manual Disk StatusESV4 User’s Manual USB Backup118ESV4 User’s Manual ESV4 User’s Manual Play the backup file with the NVR Media Player120ESV4 User’s Manual Once the file has been successfully verified, you should be prompted with the message shown below ESV4 User’s Manual122ESV4 User’s Manual ESV4 User’s Manual Login screenLocal UI from HDMI Output Live View124ESV4 User’s Manual ESV4 User’s Manual Remote control126ESV4 User’s Manual ESV4 User’s Manual Live View 128ESV4 User’s ManualESV4 User’s Manual Side menu130ESV4 User’s Manual ESV4 User’s Manual 132ESV4 User’s Manual ESV4 User’s Manual Green: Recording Dark grey: Not configuredWhite: Disconnected Blue: Connected Sequence view 134ESV4 User’s ManualESV4 User’s Manual When the focus is on the Start/stop sequence view icon, press the Right button on the remote will move the focus to the sequence interval drop-downmenu136ESV4 User’s Manual ESV4 User’s Manual 138ESV4 User’s Manual Add preset pointsPTZ Control ESV4 User’s Manual Preset point sequence view140ESV4 User’s Manual ESV4 User’s Manual Manual Recording142ESV4 User’s Manual ESV4 User’s Manual Take snapshot144ESV4 User’s Manual ESV4 User’s Manual PIP Picture-in-pictureEvent VideoTurn on Audio 146ESV4 User’s ManualESV4 User’s Manual Full ScreenDisplay video in its original size 148ESV4 User’s ManualESV4 User’s Manual Detail channel status150ESV4 User’s Manual ESV4 User’s Manual Dashboard152ESV4 User’s Manual Power offPlayback To switch to Playback, move the selection focus to the Playback button shown above and press the OK button on the remoteESV4 User’s Manual 4.Channel status 154ESV4 User’s Manual1.Take snapshot 2.Full screen 3.Display video in its original sizeESV4 User’s Manual Time Chart156ESV4 User’s Manual ESV4 User’s Manual Export recorded data158ESV4 User’s Manual ESV4 User’s Manual Camera Setup160ESV4 User’s Manual You will be presented with the “Add” action if you press the “OK” key on an empty channel. Click “OK” key again to add a new camera ESV4 User’s ManualAdd camera with Auto Search 162ESV4 User’s ManualESV4 User’s Manual You will then be taken to the next page, which will ask you for the camera’s username and password. Use the directional keys on the remote control to work with the on-screenvirtual keyboard to enter them. When done, press the “OK” key to begin detection164ESV4 User’s Manual Advance ConfigYou will be taken back to the Channel List after successfully adding a camera ESV4 User’s Manual166ESV4 User’s Manual ESV4 User’s Manual Add camera manuallySoftware Specifications168ESV4 User’s Manual HardwareNetwork ESV4 User’s ManualPlayback Recording170ESV4 User’s Manual Technology license NoticeAbout the software MODIFICATION GNU GENERAL PUBLIC LICENSE Version 2, JunePreamble GNU GENERAL PUBLIC LICENSE172ESV4 User’s Manual bAccompany it with a ESV4 User’s Manual174ESV4 User’s Manual NO WARRANTYHow to Apply These Terms to Your New Programs END OF TERMS AND CONDITIONSESV4 User’s Manual