NEGATIVE/POSITIVE Reversal, Editing | Toshiba FC15, FC22 specification

11. NEGATIVE/POSITIVE REVERSAL

In the full colour mode, this function allows you to reverse both hue and shading of the entire original when making copies. In the black mode or monocolour mode, only the shading of the entire original is reversed.

Original		Copy

Procedure

1 Press the EDIT key to enter the Editing menu, and press the Next key.

2 Press the

EDITING

key.

3

4

5

6

Press the NEG/POS key.

Select the desired copy size, image density level, reproduction ratio, copy quantity, etc. if necessary.

Place the original(s) on the original feed tray or on the glass.

●See page 22 for how to set the originals.

Press the START key.

88

Image 92

Toshiba FC15, FC22 manual NEGATIVE/POSITIVE Reversal, Editing

Contents

FC15/22 Page Storage of Colour Copies Forgery Prevention Function Preface Features of the FC15/22 Preface Table of Contents Table of Contents Precautions Installation Precautions Be sure to disconnect the power-cord plugHandle and use the copier gently and carefully Dry area Description of the Digital Copier Names of the Main Components Reversing Automatic Document Feeder Automatic DuplexerStaple Sorter Large-Capacity Feeder Settings key Description of the Control PanelInfo key Touch panel Function Clear key Stop keyStart key Clear key Settings Confirmation function Description of the Control PANELCont Description of the Message Display Colour Mode SORT/STAPLE Setting keyOriginal Mode Selection key Cassette Switch key Description of the Graphic Display Memo HOW to Make Copies Paper Acceptable Paper Types and SizesFeeder Paper Type Paper Size Remarks Instructions before use Paper Type Toshiba Recommendations / Manufacturer Size ModeRecommended Paper Forcibly Switching to Energy-saving Mode Cancelling the Energy-saving ModeENERGY-SAVING Function Press the Energy Saver or Start key on the control panel Turning on the Power Switch Turn on the power switchAbout 9 minutes later, the message Ready appears If this message appears When Placing the Original on the Glass When Using the Automatic Document FeederAuto Job Start Set the desired copy modes Press the Start key Precautions When Feeding Originals Reversing automatic document feeder Copying in the Continuous Feed Mode ADF Copying in the Single-Feed Mode Insert the original Copying in the Mixed Originals Mode SETKey Copy quantity as required Procedure Check that the Automatic Paper Selection mode is selected Select the image density level Auto Copying in the Automatic Paper Selection Mode When the Automatic Paper Selection is not Available Select the desired paper sizeReturn to the Basic menu, then select Image density level and copy quantity as Using Automatic Magnification Selection Zoom ORG. A4 KEYPress the AMS key Press the desired COPY-SIZE key Copy quantity Select the desired image density levelReduced or enlarged copies of the selected Tips KEY Selecting the Original Size and the Copy SizePress the Zoom ORG. A4 Using the Zoom Keys Down Copying in Manual Density Mode Press Key to change Copy density Copying in Automatic Density Mode Copying by Original Mode Selection Select the desired copy size, reproduction If necessary, press Key To adjust the image densityRatio and copy quantity Press the Start key Colour Mode Selecting the Colour Mode Bypass Copy Mode Bypass Copy Mode Corresponding Paper Type Maximum Capacity Bypass Copying Thick PAPER/OHP Film Select the desired paper type Set the copy quantity Thick Paper Perform to 3 onTHICK1 THICK2 THICK3 Check the type of the thick paper and press Set the copy quantity Press the Start key OHP Films Perform to 3 on Press the OHP Film keyA4 is automatically selected for the copy Size Cassette Setting for Thick PAPER/OHP Film Setting the Cassette for Thick Paper 91~105g/m2 Setting the Cassette for OHP Film Interrupt Copying Memo Colour Editing and Adjustment Monocolour Copying Level, copy quantity, etc. if necessary HUE Adjustment ColourHUE/SATURATION HUE Cancelling the Saturation Adjustment Saturation Colour Balance Ymck Adjustment Cancelling the Colour Balance AdjustmentPress the + or key to adjust the colour Colour Balance RGB Adjustment ONE-TOUCH Adjustment ONE Touch AdjustmentKey Press the desired mode key Key to enter the colour Background Adjustment Cancelling the Background AdjustmentBackground Adjustment Light Dark Sharpness Adjustment Cancelling the Sharpness AdjustmentSharpness Soft Sharp Memo Using the Editing Functions Image Shift Image Shift CopyingEdit After having adjusted the margin, press Margin on the Book OriginalsLevel, reproduction ratio and copy quantity Tip Margins can be created also in the bypass Edge Erase How to Change the Edge Erase MarginEdge Erase Copying Place the originals on the original feed Tray or on the glassLevel, reproduction ratio, copy quantity Etc. if necessary Book Centre Erase Book should be centred on the yellow Indicator line with its bottom toward youSet the originals on the glass DUAL-PAGE Copying DUAL-PAGE Select the A4 copy size Place the original on the glass Copying Procedure Full Image Copying 1 Mode Copying Set the originals on the original feed tray 1 Mode Copying Enter the number of the originalsPress the SET key Set the desired image density level, copy Duplex Copying Duplexed Copies from Single-sided Originals Duplexed Copying Place the originals Using Editing Functions Duplex Copying Finished When Placing the Original on the Glass Perform to 10 on Duplexed Copies from Two-sided OriginalsPress Key on the Basic menu Ratio, image density level, copy quantity Single-sided Copies from Two-sided Originals Press the 1→1 key on the Basic menu Key Duplexed Copies from Book Originals Select the copy size Set the next original Select Image Shift if necessaryPlace the original and press the Start key Tray or on the glass and press the Start Y ZoomPress the lower TRIMMING/MASKING TRIMMING/MASKING Specifying an areaIts bottom edge towards you and its top Place the original face up on the glass with Editing Trim Mask Trimmed or masked copies exit from the copier Mirror Image Mirror NEGATIVE/POSITIVE Reversal Centring Then press Next Key PressCentring Press the ALL or Part key to select the area for centring Press the Start key Image Repeat Then press Next KeyImage Repeat Display on the right appears Image Repeat Using the Special Functions Automatic Calibration Press the Calibration key Test Print Automatic Calibration Setting the Date and Time Time is displayed in the 24-hour system Setting the Date and TimeKey in the hour 0~23 and press Example 10 30 a.m. → 1 + 0 + Weekly Timer Setting the Weekly Timer Weekly Timer Cancelling Operation of the Weekly Timer Mode Memory Mode MemoryStoring a New Combination of Copy Modes Program Mode Memory Recalling a Stored Combination of Copy ModesPress the MEMORY1 or, MEMORY2 , ME MORY3 , MEMORY4 key Combination of modes you have Making US Standard Size Copies Press the desired size key for Universal To change to a US standard size, reset Size mark plate so that the UniversalMark appears and set the corresponding Size of paper see After you have set the originals, select Copy quantity, etc. if necessary, and pressProgramme menu Universal 106 Access Codes ID Numbers Total Counter Department Management Department Management ID Counter 111 Department, enter its access code 4 digits Clearing CountersALL If you want to clear the counter of a certain Becomes YESCounter is cleared and the number Registration/Change/Deletion of Access Codes Access Code 115 116 Following message appears KEY Copy CounterInsert the key copy counter Change of Language on the Display Panel User Selection Initial Settings 120 Using the Optional Staple Sorter Description of the Main Components Ratio, image density level, etc. if necessary NON-SORT CopyingKey in the desired copy quantity Sort or Staple Sort Copying Sort or Staple Sort Placing the originals on the glass Key in the number of copies sets Placing the original on the glass Press the Start key Using the automatic document feederSort or SORT/STAPLE Copying Manual Stapling Align the edges of the copies and insertThem into the first sort bin Press the Staple Key Group Copying When the Graphic Symbols Flash ADD Paper Symbol Adding Paper to the Front Cassette 131 ADD Paper Symbol Adding Paper to the Large-Capacity Feeder OptionalOpen the cover of the large-capacity feeder Place the paper in the large-capacity feeder Changing the Paper Size of the Cassette Shown on the cassette surfacePlace paper in the cassette Set the back guide to the desired paper size Replace Toner BAG Symbol Replacing Procedure Remove the used toner bag from the copier Close the used toner bag ADD Toner Symbol Open the front covers Slide the cartridge along the rail toward You and remove itShake the new cartridge to the right Pull the seal out from the cartridge Remove the copy receiving tray Clear Paper SymbolMisfeeding inside of the Copier 139 Clear Paper Symbol 140 13Close the exit cover 142 Misfeeding in the Automatic Duplexer Fully.of the lower guide plate, lift it slowly Close the lower guide platePush the lever, and then holding the handle Misfeeding from the Cassettes Misfeeding in the Large-Capacity Feeder Misfeeding in the Automatic Document Feeder Close the feed-side coverRemove the originals Open the feed-side cover of the automatic Misfeeding in the Bypass Guide Misfeeding in the Staple Sorter Open the stapler cover Replacing StaplesReplacing Staples Install a new staple cartridge Turn OFF the power switch of the copier Removing Jammed StaplesRemoving Jammed Staples Wing nut that holds the stapler unit 153 Call Service Symbol Periodic Maintenance Maintenance Daily Inspection Simple Troubleshooting Simple Troubleshooting SPECIFICATIONS, Accessories & Options FC15/22 Specifications 160 Specifications of Options Specifications of Options Packing List Copying Function Combination Matrix Image Quality Adjustment Combination Matrix 30,000 copies Main Service Preventative MaintenanceHow to affix the PM labels FC15/22