Turning the power on and off (Continued)
■ Turning the power off |
Basic operations
Preparations
1 Press the ON/STANDBY button. |
A message appears on the screen, confirming that you wish to shut off the power. This |
message will disappear after a moment. (This operation is no longer valid after the |
message disappears.) |
2 Press the ON/STANDBY button again. |
The screen turns off, but the internal cooling fan continues to operate for a short while. |
•Place the projector, and correctly connect all devices.
•To operate via the remote control, [PJ MODE] p.20 must be selected.
Press the PJ MODE button. The button lights up. This light will go out 30 seconds after operations are complete. If necessary, press the button again.
Remote Control
VOL.- | VOL.+ |
PJ MODE | LASER |
[PJ MODE] | MENU / ENTER |
Lights up | |
| INPUT |
Then, the projector goes into standby mode. |
When cooling lamp | During internal cooling | After cooling complete | ||||||
FAN | TEMP LAMP | ON | FAN | TEMP LAMP | ON | FAN | TEMP LAMP | ON |
(Green) | (Green) | (Orange) | (Green) | (Off) | (Orange) | (Off) | (Off) | (Orange) |
A | Flashing |
| B |
|
| C |
|
|
|
|
|
|
|
| |||
A During cooling, the LAMP indicator flashes. In this state, the power cannot be |
1Turn on the power.
Turn on the power, following the instructions in “Turning on the power” p.25 .
2Select language (When using for first time).
When the projector is used for the first time after purchase, a message is displayed on the screen, and the language menu appears. The default language is English.
(If the screen focus is not on the menu, adjust according to step 6 .)
| turned back on. In addition, unplugging the power cord in this state will shorten | |
| the life of the lamp. | |
| After the LAMP indicator goes off, the cooling fan continues to operate for a | |
B | ||
| short while, in order to expel excess internal heat. If you are in a hurry, there is | |
| no problem with unplugging the power cord in this state. | |
| In standby | |
C | ||
|
Note
• The projector consumes about 6W of power in standby (models equipped with PC card |
qUse the 
buttons to select the desired language, and press the 
button.
A message displays the selected language.
wPress the 
button to apply.
Notes
English ................ English
Français .............. French
Deutsch .............. German
Italiano ................ Italian
Español ............... Spanish
Português .......... Portuguese
................... Japanese
....... Chinese (simplified)
....... Chinese (traditional)
................... Korean
Operations
slot consume about 18W). We recommend that you unplug the power cord if you will not |
be using the projector for an extended period. |
PRECAUTIONS
• | Before unplugging the power cord, make sure that the LAMP indicator is off. Unplugging |
| the power cord and cutting off the power while the projector is running or being cooled |
| will shorten the life of the lamp. However, please unplug the power cord if the |
| projector locks up or acts abnormally. |
• | If the power cord was unplugged before cooling was complete, give the lamp sufficient |
| time to cool before plugging it back in. If the lamp overheats it may fail to light, and its |
| lifetime will be shortened. |
•After the first time the projector is turned on, the Language menu does not appear
upon startup. However, from the Reset menu p.56 select “Reset all” to display the Language menu the next time the projector is turned on.
•The language can also be set via the Display setting menu p.55 .
•This owner’s manual assumes that English has been selected.
3Place connected device(s) in operating status.
Turn on and boot up connected computers and other devices.
LCD Panels
LCD panels wear out. In order to prolong the lifetime of your LCD panel, take the following precautions.
•In order to extend the lifetime of the LCD panel, always turn off the power when not in use, and make sure that the lamp is off. Keeping the lamp off is also very effective at saving electricity.
•If the air filter becomes dirty and clogged, the projector’s internal temperature will rise, shortening the lifetime of the LCD panel and causing malfunctions. Clean the air filter from time to time p.57 , and replace it periodically. Contact the store where you purchased your projector, or your local Service Station for replacement air filters.
4Select input.
qPress the INPUT button.
A list of inputs appears on the screen.
wUse the 
buttons to select the desired input, and press the 
button.
The picture for the selected input is projected.
Computer (1)
Y/PB/PR(1)
Computer (2)
Y/PB/PR(2)
Video
PC Card
Camera
26 | 27 |
