Using the menus (Continued)
■Displaying Information (Status display)
This displays information about the input signal, lamp use time, LAN connection status, etc.
“Yes”: displayed, “No”: not displayed
How to use the PC card slot
The wireless LAN PC card enables you to connect the projector wirelessly with a personal computer that supports IEEE802.11b/g based wireless LAN. p.51 (Please note that communication between all the computers based on IEEE802.11b/g and this projector is not guaranteed.) You can also use a commercially available memory PC card to project JPEG image files using this projector. p.58
or mounting a PC card.
|
|
|
|
| Video | Wireless/ | USB |
| Item | Description | Computer Y/PB/PR | Card | memory | ||
| Projector |
|
|
|
|
|
|
| Input | Input source name | Yes | Yes | Yes | Yes | Yes |
| Mode name | RGB input mode [Note 1] | Yes | No | No | No | No |
| Resolution | Resolution (in dots) | Yes | No | No | No | No |
| Frequency | Sync frequency | Yes | No | No | No | No |
| Sync | Sync signal polarity [Note 2] | Yes | No | No | No | No |
| Signal format | Y/PB/PR signal format | No | Yes | No | No | No |
| Video mode | Color method of video signal | No | No | Yes | No | No |
| Lamp time | Time of lamp use [Note 3] | Yes | Yes | Yes | Yes | Yes |
| Lamp reset count | The count for lamp replacement | Yes | Yes | Yes | Yes | Yes |
| Total time | The total time that this projector is | Yes | Yes | Yes | Yes | Yes |
|
| used. | |||||
|
|
|
|
|
|
| |
| Version | Firmware version [Note 4] | Yes | Yes | Yes | Yes | Yes |
| Wired LAN |
|
|
|
|
|
|
| Connection status | Displays connection status of LAN. | Yes | Yes | Yes | Yes | Yes |
| IP address | Displays the IP address. | Yes | Yes | Yes | Yes | Yes |
| Subnet mask | Displays numeric value of subnet | Yes | Yes | Yes | Yes | Yes |
|
| mask. | |||||
|
|
|
|
|
|
| |
| Gateway | Displays numeric value of gateway. | Yes | Yes | Yes | Yes | Yes |
| MAC address | Displays MAC address of the | Yes | Yes | Yes | Yes | Yes |
|
| projector. [Note 5] | |||||
|
|
|
|
|
|
| |
| PJLink class | PJLink version | Yes | Yes | Yes | Yes | Yes |
Notes
1:The mode of supported RGB signals p.88 is shown.
2:Sync signal polarity shown as P (positive) or N (negative) for [H/V].
3:Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult with a store about getting a TLPLW14 replacement lamp (sold separately) prepared.
4:[Version] shows the version of the projector’s internal control program. This version is referred to for customer service, etc.
5:In case that
Note
■Mounting a PC card
qRemove the slot cover.
Press lightly on the circle (“O”) while sliding the cover in the direction of the arrow.
Slot cover
wInsert the PC card.
After making sure of the card orienta- tion, press it in firmly until it stops.
PC Card
■Removing a PC card
qLook at CARD indicator.
If it is off, proceed to step r.
CARD indicator
UNMOUNT button
wPress the UNMOUNT button.
Begins processing for PC card removal.
eWait until CARD indicator goes out.
Never remove the PC card while lit. Doing so could damage the PC card or corrupt your data.
rPress the Eject button.
Eject button
Operations
•The displayed information will not be refreshed if the status changes. To refresh the information, dismiss the display, then display it again. The information regarding wired LAN is refreshed every time it is displayed.
■ If CARD indicator turns red | CARD indicator |
| RESET |
Press the RESET switch with a thin pin or | switch |
similar implement (it is at the bottom of a |
|
recess). |
|
48 | 49 |
