28

Operations

Turning the power off

 

 

 

 

 

 

 

1

ON/STANDBY

Press ON/STANDBY after using the projector.

 

 

 

 

 

 

 

 

 

 

An instruction message appears.

 

 

 

 

 

 

 

 

 

 

 

ON/

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STANDBY

 

 

 

 

 

 

 

 

 

 

Control panel

 

 

 

 

 

 

 

 

 

 

Remote control

(Main unit side)

 

2

ON/STANDBY

Press ON/STANDBY again.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUTO

AUTO

 

 

 

Cooling starts. Once cooling is completed, the LAMP and FAN

 

 

 

 

 

 

 

indicators turn off and the standby mode is set. (The ON

 

 

 

 

KEYSTONE

SET

 

 

ON/

 

 

 

 

 

 

 

 

 

indicator turns in orange.)

 

 

 

 

 

 

 

 

 

 

 

STANDBY

 

 

 

 

 

ON /

 

VOL/ADJ.

 

 

 

 

 

 

 

 

 

 

INPUT

 

1,2

 

 

 

 

 

LAMP

ON

LAMP

ON

LAMP

ON

 

STANDBY

 

 

 

 

 

KEYSTONE

AUTO

SET

 

 

 

 

 

(Green)

(Orange)

(off)

(Orange)

(off)

(Orange)

FREEZE

MUTE

 

 

 

 

 

 

 

 

 

FAN

 

FAN

 

FAN

 

 

 

 

 

 

 

 

 

 

Flashing

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PIP

CALL

RESIZE

 

 

 

 

 

 

 

A

(Green)

B

(Green)

C

(Off)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENTER

EXIT

 

 

A

To protect the light source lamp, the LAMP indicator blinks as long as

 

 

MENU

 

 

 

 

 

 

VOL/ADJ

 

 

MENU

INPUT

 

 

 

a minimum of cooling is necessary. The power cannot be turned back

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

on during this time. Unplugging the power cord at this time will

 

 

 

 

 

 

ON/STANDBY

1,2

 

 

shorten the lamp’s duration life.

 

 

 

 

ENTER

 

EXIT

 

 

 

 

B

The cooling fan continues to run for a while to expel the heat

 

 

CT-90072

 

 

 

 

 

 

 

remaining inside. If you are in a hurry, however, you may unplug the

 

 

 

 

TEMP LAMP ON

2

 

 

 

 

 

 

BUSY

FAN

 

 

power cord at this time.

 

 

 

 

 

 

 

 

 

Indicators

 

C

The standby mode is set.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Notes

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• The projector consumes about 20W of power in the standby mode. We recommend you to

 

 

 

 

 

 

 

unplug the power cord when not using the projector for long periods of time.

 

 

 

 

 

 

 

• Be sure that the LAMP indicator has turned off before unplugging the power cord. Cutting the

 

 

 

 

 

 

 

power by unplugging the power cord while the projector is operating or the light source lamp

 

 

 

 

 

 

 

is being cooled will shorten the lamp’s duration life. Should fault or some other irregularity

 

 

 

 

 

 

 

arise with this unit, unplug the power cord.

 

 

 

 

 

 

 

 

 

 

When reinserting the power plug before the lamp has cooled, please wait until the lamp has

 

 

 

 

 

 

 

cooled sufficiently before use. When the lamp is at a high temperature, it may not light and

 

 

 

 

 

 

 

the duration life will be shortened.

 

 

 

 

Page 28
Image 28
Toshiba TLP-MT7E manual Turning the power off, Press ON/STANDBY after using the projector, Press ON/STANDBY again