Toshiba TOSVERT VF-FS1 Series instruction manual

E6581373

TOSVERT VF-FS1 series

LONWORKS® option unit

Communication Function Manual

NOTICE

1. Make sure that this instruction manual is delivered to the end user of

LONWORKS option unit.

2. Read this manual before installing or operating the LONWORKS option unit.

Keep it in a safe place for reference.

3. All information contained in this manual are subject to change without notice.

Please confirm the lates t information on our web site “ www.inverter.co.jp”.

Contents

Main Introduction Danger Warning Notes E6581373 Table of Contents Page E6581373 1. Scope 1.1. Overview 1.2. Applicable model 1.3. System configuration E6581373 2. Names and functions of main parts 2.1. Outline view 2.1.1. LIU006Z 2.1.2. LIU007Z (for VF-FS1) E6581373 2.2. Diagnostics Time (second) LED OFFLED ON 2.2.1. Service LED E6581373 2.2.2. Status LED Time (second) Continues to be OFF Continues to be ON 2.2.3. Fault LED 2.3. RS485 communication port 3. Configurations 3.1. Neuron ID 3.2. Service pin 3.3. Device interface (XIF) file 3.4. LNS Plug-in 3.6. Command & Setpoint selection (Local/Remote) 3.7. Reference parameter of the inverter Warning E6581373 4. Functional profile 4.1. Functional profile supported by this option 4.2. Object id 5. Node Object functional block 5.1. Object map 5.2. Network variables (Node Object) 5.2.1. nciLocation (Location Label) 5.2.2. nviRequest (Object Request) 5.2.3. nvoStatus (Object Status) - 16 - 6. ACMotorDrive functional block 6.1. Object map The object map is the following. nvoxxxxxxxxxxx SNVT xxxxxxxx nvixxxxxxxxxxxx SNVT xxxxxxxx 6.2. Network variable list (VSD_6010_11) 6.3. Network variable list (the other) 6.4. Configuration properties 6.4.1. nciMaxSpeed (Maximum Speed) 6.4.2. nciMinSpeed (Minimum Speed) 6.4.3. nciRcvHrtBt (Receive Heartbeat Time) 6.4.4. nciSndHrtBt (Send Heartbeat Time) 6.4.5. nciMinOutTm (Minimum Send Time) 6.4.6. nciNmlSpeed (Nominal Motor Speed in min-1) 6.4.7. nciNmlFreq (Nominal Motor Frequency) 6.4.8. nciRampUpTm (Ramp Up Time) 6.4.9. nciRampDownTm (Ramp Down Time) 6.4.10. nciDrvSpeedScale (Default value for nviDrvSpeedScale) 6.4.11. nciPwUpOutTm (Power up delay time). 6.5. Input network variables 6.5.1. nviDrvSpeedStpt (Drive Speed Setpoint) 6.5.2. nviDrvSpeedScale (Drive Speed Setpoint Scaling) 6.5.3. nviResetFault (Fault Reset Command) 6.5.4. nviInvSetFreq (Frequency Setpoint) 6.5.5. nviRelay1 /nviDigitalOut1,2 (Control of Digital Output) 6.5.6. nviDigitalOutput (Control of All Digital Outputs) 6.5.7. nviAnalogOut1,2 (Control of Analog output) 6.5.8. nviEmergOverride (Emergency stop) 6.5.9. nviParamCmd (Parameter access) 6.6. Output network variables 6.6.1. Output network variable update 6.6.2. nvoDrvCurnt (Drive Output Current) 6.6.3. nvoDrvSpeed (Drive Speed Feedback) 6.6.4. nvoDrvRunHours (Drive Total Running Hours) 6.6.6. nvoDrvFeedback (Velocity Feedback) 6.6.7. nvoStatusWord (Inverter Status) 6.6.8. nvoDrvAlarm (Alarm) 6.6.9. nvoAlarmWord (Alarm Status) 6.6.10. nvoDrvThermal (Drive Thermal State) 6.6.11. nvoMotorThermal (Motor Thermal State) 6.6.12. nvoTorque (Motor Torque Monitor) 6.6.13. nvoDrvEnergy (Cumulative Input Energy) 6.6.14. nvoDigitalInput (All Digital Inputs Monitor) 6.6.15. nvoDigitalIn1 to 8 (Digital Input Monitor) 6.6.16. nvoAnalogIn1 to 3 (Analog Input Monitor) 6.6.17. nvoEmergStatus (Emergency Status) 6.6.18. nvoParamResp (Parameter Access Response) 6.6.19. nvoTypeVer (Identification) 7. Example usage 7.1. Procedure Bind 7.2. Binding Building Management system 7.4. Communication health management 7.5. Parameter access method E6581373 8. Specifications