Example usage, Procedure, Binding | Toshiba TOSVERT VF-FS1 Series

E6581373

7. Example usage

7.1. Procedure

Lower example shows the procedure to send the 100% speed drive command to the inverter. 1. Commission

Make a network tool to identify this option by using service pin function (refer to network tool manual in detail).

2. Binding

Refer to next section. 3. Configurations

Set correct value into the configuration properties. 4. Local/Remote

Confirm that the inverter is in Remote control mode. Otherwise set Remote control mode. 5. Drive command and setpoint

Set the {200, 1} (100% speed drive) into the nviDrvSpeedStpt and propagate it.

7.2. Binding

Network variable bound to the other network variable can transmit/receive the data. “Binding” can be made by network tool. Network variable has a direction (Input/Output) and individual type (SNVT_type). Binding to the same direction variable or the different type is prohibited.

Example connection

Fan Coil Unit	Bind	ACMotorDrive			Building
Controller		functional block			Management
					system
nvoFanSpeed		nviDrvSpeedStpt
SNVT_switch		SNVT_switch
		nvoDrvSpeed		nviDrvSpeed
					_lev_percent
		SNVT_lev_percent		SNVT	_lev_percent

Bind

7.3. Option unit reset method

One method to reset the option unit is cycling the inverter power source. The other is using reset command by network tool.

- 33 -

Image 34

Toshiba TOSVERT VF-FS1 Series instruction manual Example usage, Procedure, Binding, Option unit reset method

Contents

E6581373 Introduction Handling in general Table of Contents E6581373 Overview System configurationScope Applicable model LIU006Z Names and functions of main partsOutline view LIU007Z for VF-FS1 Service LED DiagnosticsLED LED on LED OFF Fault LEDStatus LED OFF RS485 communication port Inverter configurations ConfigurationsService pin Device interface XIF file Neuron ID Command & Setpoint selection Local/Remote LIU007Z Reference parameter of the inverter Functional profile supported by this option Functional profileObject id Object map Node Object functional blockNetwork variables Node Object NciLocation Location Label NviRequest Object Request NvoStatus Object Status ACMotorDrive functional block Object map is the following Network variable list VSD601011 LIU Network variable list the other NciMaxSpeed Maximum Speed Configuration propertiesNciMinSpeed Minimum Speed NciSndHrtBt Send Heartbeat Time NciRcvHrtBt Receive Heartbeat TimeNciMinOutTm Minimum Send Time NciNmlFreq Nominal Motor Frequency NciNmlSpeed Nominal Motor Speed in min-1NciRampUpTm Ramp Up Time NciPwUpOutTm Power up delay time NciDrvSpeedScale Default value for nviDrvSpeedScaleNciRampDownTm Ramp Down Time NviDrvSpeedStpt Drive Speed Setpoint NviResetFault Fault Reset CommandInput network variables NviDrvSpeedScale Drive Speed Setpoint Scaling NviDigitalOutput Control of All Digital Outputs NviInvSetFreq Frequency SetpointNviRelay1 /nviDigitalOut1,2 Control of Digital Output LIU007Z LIU006Z NviAnalogOut1,2 Control of Analog output NviEmergOverride Emergency stop Lnlearncurrent NviParamCmd Parameter accessLnrecall Lnlearnvalue Output network variables NvoDrvFeedback Velocity Feedback NvoDrvAlarm AlarmNvoStatusWord Inverter Status NvoMotorThermal Motor Thermal State NvoAlarmWord Alarm StatusNvoDrvThermal Drive Thermal State NvoTorque Motor Torque Monitor NvoDigitalInput All Digital Inputs Monitor NvoDrvEnergy Cumulative Input EnergyNvoDigitalIn1 to 8 Digital Input Monitor NvoAnalogIn1 to 3 Analog Input Monitor NvoEmergStatus Emergency Status Ascii NvoParamResp Parameter Access ResponseNvoTypeVer Identification Toshiba Example usage ProcedureOption unit reset method Binding Communication health management Parameter access method E6581373 Specifications ANSI/EIA/CEA