Reference parameter of the inverter | Toshiba TOSVERT VF-FS1 Series

E6581373

3.7. Reference parameter of the inverter

Reference parameter of the inverter is listed below.

	Title		Name	Description
	acc		Acceleration time
	dec		Deceleration time
	fh		Maximum frequency	Do not change these parameters, because
	ul		Upper limit frequency	the LONWORKS option unit using them.
	ll		Lower limit frequency
	vl		Base frequency 1
				Network command has priority when the
	cmod		Command mode selection	inverter is Remote mode. (See previous
				section)
				Network setpoint has priority when the
	fmod		Setpoint mode selection	inverter is Remote mode. (See previous
				section)
	f111	...	Logic input terminal function	Set proper value if use (See the inverter
	f111	...	Logic input terminal function	instruction manual).
				instruction manual).
	f603		Emergency stop selection	For “nviEmergOverride”
	f800		Communication baud rate	Set “1” (default)
	f801		Communication parity	Set “1” (default)
	f803		Communication error trip time	Set properly value
	f829		Communication protocol	Set “1” (MODBUS)

	f851		Operation at network disconnection	See “section 7.4 Communication health
	f851		Operation at network disconnection	management”.
				management”.

Warning

Mandatory

For LIU007Z, set up “Communication error trip function (f803, see the inverter instruction manual for details)” to stop the inverter when this option unit is deactivated by an unusual event such as tripping, an operating error, power outage, failure, etc. Deactivated option unit may cause an accident, if the “Communication error trip function” is not properly set up.

- 11 -

Image 12

Toshiba TOSVERT VF-FS1 Series instruction manual Reference parameter of the inverter

Contents

E6581373 Introduction Handling in general Table of Contents E6581373 System configuration ScopeOverview Applicable model Names and functions of main parts Outline viewLIU006Z LIU007Z for VF-FS1 Diagnostics Service LEDLED Fault LED Status LEDLED on LED OFF OFF RS485 communication port Configurations Service pin Device interface XIF fileInverter configurations Neuron ID Command & Setpoint selection Local/Remote LIU007Z Reference parameter of the inverter Functional profile Functional profile supported by this optionObject id Node Object functional block Object mapNetwork variables Node Object NciLocation Location Label NviRequest Object Request NvoStatus Object Status ACMotorDrive functional block Object map is the following Network variable list VSD601011 LIU Network variable list the other Configuration properties NciMaxSpeed Maximum SpeedNciMinSpeed Minimum Speed NciRcvHrtBt Receive Heartbeat Time NciSndHrtBt Send Heartbeat TimeNciMinOutTm Minimum Send Time NciNmlSpeed Nominal Motor Speed in min-1 NciNmlFreq Nominal Motor FrequencyNciRampUpTm Ramp Up Time NciDrvSpeedScale Default value for nviDrvSpeedScale NciPwUpOutTm Power up delay timeNciRampDownTm Ramp Down Time NviResetFault Fault Reset Command Input network variablesNviDrvSpeedStpt Drive Speed Setpoint NviDrvSpeedScale Drive Speed Setpoint Scaling NviInvSetFreq Frequency Setpoint NviRelay1 /nviDigitalOut1,2 Control of Digital OutputNviDigitalOutput Control of All Digital Outputs LIU007Z LIU006Z NviAnalogOut1,2 Control of Analog output NviEmergOverride Emergency stop NviParamCmd Parameter access LnrecallLnlearncurrent Lnlearnvalue Output network variables NvoDrvAlarm Alarm NvoDrvFeedback Velocity FeedbackNvoStatusWord Inverter Status NvoAlarmWord Alarm Status NvoDrvThermal Drive Thermal StateNvoMotorThermal Motor Thermal State NvoTorque Motor Torque Monitor NvoDrvEnergy Cumulative Input Energy NvoDigitalInput All Digital Inputs MonitorNvoDigitalIn1 to 8 Digital Input Monitor NvoAnalogIn1 to 3 Analog Input Monitor NvoEmergStatus Emergency Status NvoParamResp Parameter Access Response NvoTypeVer IdentificationAscii Toshiba Procedure Option unit reset methodExample usage Binding Communication health management Parameter access method E6581373 Specifications ANSI/EIA/CEA