Manuals / Vanguard Managed Solutions / Computer Equipment / Network Card

Vanguard Managed Solutions 650 Choosing a Site, 2. Proper Cable and Air Clearance

Models: 650

1 82

Download 82 pages 61.12 Kb

Page 33

Image 33

Choosing a Site

Introduction

How to Choose a Site for the Vanguard 65x

This section describes how to choose an appropriate site for your Vanguard 650 Series hardware.

Choose a site that is within an appropriate distance of a power source. Depending on your application, and the country in which the Vanguard 650 Series will operate, the power source must be a grounded 100 to 240 VAC outlet.

To avoid overheating the circuitry, never place anything on top of the unit. Also, leave at least 2 inches (5 cm) of clearance in front of the front panel, to allow you to see the unit’s LEDs, and behind the unit for interfacing cable clearance, as shown in Figure 2-2.

The selected site should be free of accumulated dust and environmental extremes.

Minimum 2 inches (5cm)

Front and Rear

Do Not Place Anything on Top of Unit

Figure 2-2. Proper Cable and Air Clearance

Installing 650 Series Hardware

2-3

Page 33

Image 33

Vanguard Managed Solutions 650 installation manual Choosing a Site, Introduction How to Choose a Site for the Vanguard

Contents

650 Series Installation Manual Vanguard Managed Solutions651/652 Models STATUS ISDN-DProprietary Material Safety WarningsProduct Declarations and Regulatory Information Internet InformationPower Supply Hazardous VoltagePOTS Connection Connecting Ports Socket Outlet InstallationPSTN Direct Connection Chapter 2. Installing 650 Series Hardware ContentsChapter 3. Installing and Coldloading 650 Series Software About This Manual Customer Information Customer Response CardAppendix A. Specifications Contents continuedReturn Procedures Index Appendix B. Software License and Regulatory InformationOverview About This ManualIntroduction AudienceMise en Garde About This Manual continuedVorsicht AvertissementVanguide ONS About This Manual continued Related DocumentationCD-ROM OtherPage Customer Customer InformationQuestions Comments AboutPage Document Title 650 Series Installation Manual Customer Response CardPage Getting Started ChapterIn This Chapter TopicWhat Is the 650? ConfigurationsSupported ProtocolsStandard Features Vanguard 650 Series FeaturesISDN Service MultiprotocolSample Network Topology Figure 1-2. Sample 650 Network TopologyIntroduction 651/653 - Data Only Connector TypeExternal Designation Internal CTPConnector Type 652/654 POTS With/Without Battery BackupIntroduction External Designation652/654 With POTS Support Types of Equipment Supported POTS Support GuidelinesIntroduction Battery Pack 652/654 With POTs and Battery BackupBattery Backup RechargeableWith Battery BackupStoring the Hardware Introduction 651/653 Hardware Components652/654 Hardware Components Front Panel Detailed 650 Series Front PanelFigure 1-3. 650 Front Panel LED’s IntroductionPanel DIP Switches Figure 1-4. 650 Front Panel SwitchesSwitch Switch NameDetailed 650 Series Rear Panel Figure 1-5. 650 Series Rear Panel ConnectorsPower Supply PowerSoftware IntroductionStep Figure 1-7. Software Option Statistics - Screen 2 of Figure 1-6. Software Option Statistics - Screen 1 ofSoftware Getting StartedPage See This Procedure Installing 650 Series Hardware OverviewChapter Follow These StepsChecking Your Shipment Contents Figure 2-1. Vanguard 650 Series Shipment ContentsIntroduction Introduction How to Choose a Site for the Vanguard Choosing a SiteFigure 2-2. Proper Cable and Air Clearance Cabling the 650 Series Figure 2-3. 650 Series Back PanelIntroduction Air Circulation Cable ClearanceISDN Cable Data 1 and DataFigure 2-4. 4-Wire and 2-Wire Modem Strapping Positions Changing theModem Strapping Powering Up Powering Up the Vanguard 650 SeriesDiagnosing Start up FailuresRemoving the Top Cover and Front Panel Panel RemovalFigure 2-5. Opening the 650 Series Introduction Installing and Coldloading 650 Series SoftwareSee Page See This ProcedureBoot PROM Boot PROM650 Operating Software and Option Images ImageWhere to Get Where to Get Operating SoftwareOperating Software File FormatsSoftware Description continuedFilename Option Image Name 21 RenoHow To Installing SoftwareVanguide Application SetColdloading Coldloading 650 Series Operating SoftwareSoftware ResponseResponse continued ActionStep Before You Begin Loading Software via TFTP DownloadIntroduction StepDISABLED DISABLED. The node is ready forA node boot is required Disable and Boot? y/nApplication Downloading Software Using the Software LoaderManager Figure 3-1. Vanguide Application Manager WindowFigure 3-2. Software Loader Window LoaderStep ActionFigure 3-3. Software Loader Verification Dialog Box Action continuedFigure 3-4. Software Loader Status Box Or Click No to cancel the download operationFigure 3-5. Vanguard Software Loader Error Message Box Vanguard Configuration Loader Vanguard Configuration Loader Downloading Configuration Memory CMEMFigure 3-6. Configuration Loader Window StepConfiguration Figure 3-7. Configuration Loader Verification Dialog BoxLoader Error Figure 3-8. Vanguard Configuration Loader Error Dialog BoxVanguide Terminal How To UseOverview Vanguide TerminalFigure 3-10. Control Port Main Menu Main MenuStep ActionIntroduction Linking Software Images Using Software BuilderSaving and Selecting a Predesigned ConfigurationRestoring CMEMs To UseWhen to Save Restore Initiating Save Restore Operations Using the CTP Selecting a Predesigned Configurations Using the CTPFigure 3-11. Configuration Save/Restore Menu RestoringUsing Kermit Saving and Restoring Configurations Using KermitSaving ResultStep Restoring Configurations Using KermitAction ResultUsing TFTP Saving and Restoring Configurations Using TFTPConfigurations IntroductionConfigurations Using TFTPRestoring Appendix A Specifications OverviewIn This Appendix SpecificationsProduct Specifications Power Requirements Power Supply Description Safety PhysicalHardware Environmental Electromagnetic Compatibility Connector Pinouts Figure A-1. RJ11/RJ45 Connector Pin NumberingISDN Cable Description IntroductionData 1 and Data 2 Cable Descriptions Interface Signal NameCable Pinout Pinout4-Wire Modem Signal2-Wire RJ45 to DB25Interface Signal Name DB25 Pin #Interface Signal Name Modem SignalInterface Signal Name Data 2 DB25Pinout Pin #Page Software License and Regulatory Information In This Appendix Appendix BVanguard SeriesRESTRICTED RIGHTS LEGEND If the Software is procured for use by any U.S. Government entity other than the Department of Defense, the following notice applies Introduction Product Declarations and Regulatory Information Product Declarations and Regulatory InformationCE Marking D130 978JApproval French DRGNetherlands Radio FrequencyRequirements Canadian Department of Communications Safety Warnings AvertissementWarnung Page Return Procedures Introduction For LocationsContact Packaging Factory RepairGuidelines for Equipment ReturnIndex