Vision 50/CineWide with Lens Base Plate | Vidikron manual

Installation

To install the fixed CineWide base plate on a Vision 50/CineWide:

1.Place the projector upside down on a blanket or other soft surface.

2.Line up the four mounting holes on the CineWide base plate with those on the bottom of the projector.

3.If you are mounting the Vision 50/CineWide on a ceiling: Line up the four holes on the projector ceiling mounting plate (included with the projector ceiling mount kit) with those on the bottom of the projector.

Note	The hole pattern on the CineWide base plate is identical to that on the
	ceiling mounting plate.

4.Secure the CineWide base plate (and ceiling mounting plate, if needed) to the projector with the four, M6x16mm screws and washers provided with the CineWide lens base plate. See Figure 3-8.

1. Do not use the mounting screws provided with the ceiling mounting Caution plate. Use only the hardware provided with the CineWide lens base

plate.

2.DO NOT OVER-TIGHTEN THE SCREWS.

Vision 50/CineWide with Lens Base Plate	Vision 50/CineWide with Lens Base Plate and
	Ceiling Mounting Plate

Figure 3-8. Vision 50/CineWide with Anamorphic Lens Base Plate and Ceiling Mounting Plate - Bottom View

Installing the Fixed CineWide Base Plate (Vision 50/CineWide)

Vidikron Vision 50 Series Owner’s Operating Manual

23

Image 35

Vidikron manual Installing the Fixed CineWide Base Plate Vision 50/CineWide, Vision 50/CineWide with Lens Base Plate

Contents

Series DLP Projectors Page For Projectors, Video Processors and Controllers TWO Year Limited Warranty Effective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Maintenance and Troubleshooting Serial Communications Table of Contents 1List of Figures List of Figures Xii About This Manual 1Introduction If you need Turn to Using This ManualThey also provide supplemental information Performance or cause a malfunction Description, Features and Benefits Optional Accessories Vision 50 at a Glance POWER/STANDBY LED Indicates power status as follows Temp LED Cable Access Door Open to access connectors Vision 50 Connector PanelRefer to Vision 50 Connector Panel, below Volt 250 mA Trigger Output 3.5-mm, mini phono jack Comp 1 RCA connectorsBuilt-In Keypad Hdmi Digital Vision 50 Remote Control Vision 50 Remote Control Comp 2 HD Component On / OFFSource Selection Buttons Comp 1 SD Component VID S-Video VAC V2 Aperture Control Memory Preset ButtonsCursor Keys Picture-In-Picture PIP / Picture-By-Picture PBP Controls Motorized Lens Controls Remote Control/Built-In Keypad Functional Comparison Operation 3InstallationRemote Control If installing a Vision 50/CineWide or Vision 50/CineWide Quick SetupInstallation Overview Step Procedure For Details, Refer to Advantages Considerations Installation ConsiderationsProjector Installation Options Installation Type Vision Throw Ratios for the Vision 50 SeriesThrow Range Throw Ratio Projector Model Position Ceiling InstallationFloor Installation Vertical and Horizontal Folded Optics Installing the Optional CineWide Lens Mount With AutoScope Vision 50 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Vision 50/CineWide with Lens Base Plate Installing the Fixed CineWide Base Plate Vision 50/CineWide Ceiling Mounting Inverted Adjusting the ProjectorMounting the Vision Floor Mounting Upright Hdmi or DVI Source Connector Panel AccessConnecting Source Connections to the Vision DVD Player or HD Set Top Box Personal Computer 10. RGB Connections DTV or Progressive Component YPbPr Source 11. Progressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc 12. Composite, S-Video and Component Video Connections 13. RS-232 Control System Connection Equipment 15. Connecting the 12-volt Trigger Output to Other Equipment Power source Turning on the PowerConnecting to AC Power Focus Zoom Vertical Lens Shift Primary lens is perfectly centered on the screen Installing and Adjusting the CineWide Anamorphic LensAnamorphic Lens Installation Adjustment Vision 50/CineWide Adjusting the Lens Height Y Anamorphic Lens Top View AutoScope AdjustmentVision 50/CineWide with 18. Attaching the Anamorphic Lens to the Lens Adapter Ring Attach Lens Mounting Assembly to Lens Motor Carriage Plate Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Installation Selecting an Aspect Ratio Selecting An Input Source Using Picture-In-Picture/ Picture-By-Picture PIP/PBP4Operation Selecting Video Memory Using the On-Screen Menus Picture AdjustInstallation Service Main Menu Picture Adjust Typical Pluge Pattern for Adjusting Brightness Perform the adjustments in the order listed here Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image Option Description Aspect Ratio Settings Remote Projector Status Exit to return to the previous menu or Menu to exit Installation Service Service Operation Operation Remote Control ISF Calibration ISF Calibration Operation Operation Lamp assembly for replacement 5Maintenance and TroubleshootingLamp Replacement Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Temp and Lamp LEDs are both Maintenance and Troubleshooting 6Serial Communications Serial Command SyntaxRS-232 Connection and Port Configuration Serial Commands Serial Communications Serial Commands Serial Commands Vision 50 Specifications 7Specifications Dimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power Requirements Regulatory Approvals Limited WarrantySpecifications are subject to change without notice Vision 50 Dimensions with Optional Fixed Anamorphic Lens Vision 50 Dimensions Vidikron Vision 50 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron