Quick Setup, Installation Overview | Vidikron Vision 50 instruction

Installation

3.2

Quick Setup

Table 3-1gives a quick overview of the Vision 50 installation process. The sections following this one provide detailed instructions.

Installation should be performed by a qualified custom video installation

Note specialist.

Table 3-1. Installation Overview

	Step	Procedure	For Details, Refer to
	Step	Procedure	page...
			page...

	1	Choose a location for the projector	15

		If installing a Vision 50/CineWide or Vision 50/CineWide	19
	2	with AutoScope: Install fixed CineWide base plate or
		AutoScope lens motor (optional)

	3	Mount the projector	24

	4	Connect signal sources to the Vision 50	25

	5	Connect external controller to RS-232 port (optional)	29

	6	Connect 12-volt trigger output to AutoScope lens motor or	30
	6	other equipment (optional)
		other equipment (optional)

	7	Apply power to the projector	31

	8	Change the OSD Language (optional)	32

	9	For rear-screen and/or ceiling-mount installations, select the	32
	9	proper picture orientation
		proper picture orientation

	10	Primary lens adjustments: projected image size (zoom),	17, 32
	10	position (shift) and focus
		position (shift) and focus

	11	Install CineWide anamorphic lens (optional)	33

	12	CineWide lens adjustments: position, pitch (angle), geometry	38
	12	and focus
		and focus

		Projector calibration: adjust the following for each input,	51 through 57
		starting with Component 1; save settings when finished:
		• Aspect ratio
	13	• Brightness
	13	• Contrast
		• Contrast
		• Color level
		• Tint
		• Input position

14	Vidikron Vision 50 Series Owner’s Operating Manual

Image 26

Vidikron Vision 50 manual Quick Setup, Installation Overview, Step Procedure For Details, Refer to

Contents

Series DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and Controllers Effective Warranty Date Vidikron Safety Precautions 1Table of Contents Maintenance and Troubleshooting Operation Serial Communications Table of Contents 1List of Figures List of Figures Xii 1Introduction About This Manual Performance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn to Description, Features and Benefits Optional Accessories POWER/STANDBY LED Indicates power status as follows Vision 50 at a Glance Temp LED Cable Access Door Open to access connectors Vision 50 Connector PanelRefer to Vision 50 Connector Panel, below Hdmi Digital Comp 1 RCA connectorsBuilt-In Keypad Volt 250 mA Trigger Output 3.5-mm, mini phono jack Vision 50 Remote Control Vision 50 Remote Control VID S-Video On / OFFSource Selection Buttons Comp 1 SD Component Comp 2 HD Component Picture-In-Picture PIP / Picture-By-Picture PBP Controls Memory Preset ButtonsCursor Keys VAC V2 Aperture Control Remote Control/Built-In Keypad Functional Comparison Motorized Lens Controls Operation 3InstallationRemote Control Step Procedure For Details, Refer to Quick SetupInstallation Overview If installing a Vision 50/CineWide or Vision 50/CineWide Installation Type Installation ConsiderationsProjector Installation Options Advantages Considerations Projector Model Throw Ratios for the Vision 50 SeriesThrow Range Throw Ratio Vision Vertical and Horizontal Ceiling InstallationFloor Installation Position Folded Optics Installing the Optional CineWide Lens Mount With AutoScope Vision 50 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 50/CineWide Vision 50/CineWide with Lens Base Plate Floor Mounting Upright Adjusting the ProjectorMounting the Vision Ceiling Mounting Inverted Connections to the Vision Connector Panel AccessConnecting Source Hdmi or DVI Source 10. RGB Connections DVD Player or HD Set Top Box Personal Computer 11. Progressive Component Video Connections DTV or Progressive Component YPbPr Source 12. Composite, S-Video and Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc 13. RS-232 Control System Connection 15. Connecting the 12-volt Trigger Output to Other Equipment Equipment Power source Turning on the PowerConnecting to AC Power Focus Zoom Vertical Lens Shift Primary lens is perfectly centered on the screen Installing and Adjusting the CineWide Anamorphic LensAnamorphic Lens Installation Adjustment Vision 50/CineWide Adjusting the Lens Height Y Anamorphic Lens Top View AutoScope AdjustmentVision 50/CineWide with Attach Lens Mounting Assembly to Lens Motor Carriage Plate 18. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Installation Selecting Video Memory Using Picture-In-Picture/ Picture-By-Picture PIP/PBP4Operation Selecting an Aspect Ratio Selecting An Input Source Using the On-Screen Menus Service AdjustInstallation Picture Picture Adjust Main Menu Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image Option Aspect Ratio Settings Description Remote Projector Status Installation Exit to return to the previous menu or Menu to exit Service Service Operation Operation Remote Control ISF Calibration ISF Calibration Operation Operation Lamp assembly for replacement 5Maintenance and TroubleshootingLamp Replacement Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Temp and Lamp LEDs are both Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration 6Serial Communications Serial Communications Serial Commands Serial Commands 7Specifications Vision 50 Specifications Power Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications Dimensions Regulatory Approvals Limited WarrantySpecifications are subject to change without notice Vision 50 Dimensions Vision 50 Dimensions with Optional Fixed Anamorphic Lens Vidikron Vision 50 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron