On / OFF, VID S-Video, Comp 2 HD Component | Vidikron Vision 50

Controls and Functions

1.ON / OFF

Use these buttons to turn the projector on or off.

2.Source Selection Buttons:

COMP 1 (SD Component)

Press to select Component 1 (SD 480i/576i) video input as the source.

S-VID (S-Video)

Press to select the S-Video input as the source.

VIDEO

Press to select Composite video input as the source.

COMP 2 (HD Component)

Press to select Component 2 (HD 480p/576p/720p/1080i) video input as the source.

RGB HD

Press to select the Component 2 RGB input.

HDMI

Press to select the HDMI input.

3.Aspect Ratio Selection Buttons

Use these buttons to select an aspect ratio directly, as follows:

ANA (Anamorphic)

For viewing 16:9 DVDs or HDTV programs in their native aspect ratio.

4X3 (Standard 4:3)

Scales the input signal to fit 4:3 display mode in the center of the screen.

L-BOX (Letterbox)

For viewing LaserDisc movies or non-anamorphic DVDs on a 16:9 screen.

I-WIDE (IntelliWide)

Enlarges a 4:3 image horizontally in a NON-linear fashion to fit 16:9 full screen display.

CINEMA

For viewing 2.35:1 source material.

C-FILL (CineWide-equipped projectors only)

Selects the Cinema Fill aspect ratio, used for viewing 16:9 source material on a 2.35:1 screen.

10	Vidikron Vision 50 Series Owner’s Operating Manual

Image 22

Vidikron Vision 50 On / OFF, Source Selection Buttons Comp 1 SD Component, VID S-Video, Comp 2 HD Component, 4X3 Standard

Contents

Series DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and Controllers Effective Warranty Date Vidikron Safety Precautions 1Table of Contents Maintenance and Troubleshooting Operation Serial Communications Table of Contents 1List of Figures List of Figures Xii 1Introduction About This Manual Performance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn to Description, Features and Benefits Optional Accessories POWER/STANDBY LED Indicates power status as follows Vision 50 at a Glance Temp LED Refer to Vision 50 Connector Panel, below Vision 50 Connector PanelCable Access Door Open to access connectors Hdmi Digital Comp 1 RCA connectorsBuilt-In Keypad Volt 250 mA Trigger Output 3.5-mm, mini phono jack Vision 50 Remote Control Vision 50 Remote Control VID S-Video On / OFFSource Selection Buttons Comp 1 SD Component Comp 2 HD Component Picture-In-Picture PIP / Picture-By-Picture PBP Controls Memory Preset ButtonsCursor Keys VAC V2 Aperture Control Remote Control/Built-In Keypad Functional Comparison Motorized Lens Controls Remote Control 3InstallationOperation Step Procedure For Details, Refer to Quick SetupInstallation Overview If installing a Vision 50/CineWide or Vision 50/CineWide Installation Type Installation ConsiderationsProjector Installation Options Advantages Considerations Projector Model Throw Ratios for the Vision 50 SeriesThrow Range Throw Ratio Vision Vertical and Horizontal Ceiling InstallationFloor Installation Position Folded Optics Installing the Optional CineWide Lens Mount With AutoScope Vision 50 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 50/CineWide Vision 50/CineWide with Lens Base Plate Floor Mounting Upright Adjusting the ProjectorMounting the Vision Ceiling Mounting Inverted Connections to the Vision Connector Panel AccessConnecting Source Hdmi or DVI Source 10. RGB Connections DVD Player or HD Set Top Box Personal Computer 11. Progressive Component Video Connections DTV or Progressive Component YPbPr Source 12. Composite, S-Video and Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc 13. RS-232 Control System Connection 15. Connecting the 12-volt Trigger Output to Other Equipment Equipment Connecting to AC Power Turning on the PowerPower source Focus Zoom Vertical Lens Shift Anamorphic Lens Installation Adjustment Vision 50/CineWide Installing and Adjusting the CineWide Anamorphic LensPrimary lens is perfectly centered on the screen Adjusting the Lens Height Y Anamorphic Lens Top View Vision 50/CineWide with AdjustmentAutoScope Attach Lens Mounting Assembly to Lens Motor Carriage Plate 18. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Installation Selecting Video Memory Using Picture-In-Picture/ Picture-By-Picture PIP/PBP4Operation Selecting an Aspect Ratio Selecting An Input Source Using the On-Screen Menus Service AdjustInstallation Picture Picture Adjust Main Menu Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image Option Aspect Ratio Settings Description Remote Projector Status Installation Exit to return to the previous menu or Menu to exit Service Service Operation Operation Remote Control ISF Calibration ISF Calibration Operation Operation Lamp Replacement 5Maintenance and TroubleshootingLamp assembly for replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Temp and Lamp LEDs are both Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration 6Serial Communications Serial Communications Serial Commands Serial Commands 7Specifications Vision 50 Specifications Power Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications Dimensions Specifications are subject to change without notice Limited WarrantyRegulatory Approvals Vision 50 Dimensions Vision 50 Dimensions with Optional Fixed Anamorphic Lens Vidikron Vision 50 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron