SAFETY FEATURES

A.Freeze Protection

If the temperature in the spa plumbing falls below 50 degrees Fahrenheit (10 degrees celsius), the water pump will turn on low speed and run for one minute. After one minute, if the water is still at 50 F, the heater will turn on and raise the temperature 10 Degrees. The top side control will display the message "ICE" to indicate potential freeze conditions.

B.Flow Protection

If the flow of water through the heater is insufficient, the spa controller will automatically turn off the heater to prevent overheating. The display will show "FLO", indicating a flow restriction caused by a clogged filter or pump impeller, a malfunction of the pressure switch or a defective pump motor. Refer to the Trouble Shooting Chart. If you cannot pinpoint the cause, Call DM Industries Ltd's Service Center for technical assistance.

C.Overheat Protection.

If a malfunction occurs and the spa water temperature reaches 112F, the pump and heater will turn off. DO NOT ENTER THE WATER. Remove the cover and allow the water temperature to cool down to 104 F. Reset the system using the procedure on page 11, section G: Resetting Your Spa. The pump and heater will start normal opera- tion when the water temperature reaches 104F. If this happens a second time in a row,

UNPLUG THE SPA AND CALL DM INDUS- TRIES SERVICE CENTER FOR ASSISTANCE.

If there is an overheat condition in the spa heater, the display will show the message "HILI". DO NOT ENTER THE WATER. Remove the cover and allow the water to cool down to 104F. Then reset the system by holding down the "DOWN" button for 5 seconds. If the "HILI" message returns, UNPLUG THE SPA AND CALL DM INDUSTRIES LTD'S SERVICE CENTER FOR ASSISTANCE.

MAINTENANCE

LINER

Your spa liner will last many years when properly used and maintained. The primary cause of failure is the improper care of the water. A regular program of water treatment as outlined in "Important Maintenance Procedures" is essential. Avoid a low pH. as this will cause unsightly wrinkles to form in the liner.

Cleanliness - Empty your voyager and refill with clean water every 2 to 3 months or when it becomes

cloudy and proper water chemistry does not clear it up. While empty, use a mild non-foaming soap solution or mild detergent to wipe away any soil or stains on the liner. Rinse thoroughly before refilling the spa. Do not use cleaning aids such as steel wool, stiff bristle brushes or abrasive cleaners.

Storage - Always dry the liner if you want to move the Voyager or store it for a period of time. It is recommended to store the liner in a warm dry place.

Repair - If your liner gets torn or punctured, a repair Vinyl Kit can be bought from your retailer or obtained by calling DM Industries Ltd.'s Service Center. A secure, unnoticeable repair can usually be made.

COVER - Fading and discoloration will occur with extended exposure to the sun and water chemicals. This will not affect its integrity and its insulation value. We recommend to clean the cover monthly to maintain its original appearance. Just hose it down and scrub it using a sponge with a mild soap solution. Rinse it thoroughly and let it dry prior to placing it back on the spa. If your cover is punctured, repair it with the repair kit provided.

Filter Cartridge Removal and Cleaning

Clean your filter every 4 to 6 weeks depending on usage. Turn the spa off by unplugging the GFCI and proceed as follows:

1.Remove the filter by pulling it down.

2.Rinse the filter using a garden hose. Rotate and separate the filter pleats while spraying water to remove all debris possible. Let the filter dry and then look for calcium deposits (scaling) or an oil film. If you find these, you will need to deep clean the filter cartridge with a filter cleaning solution to break down and remove mineral deposits and oils. The filter cartridge should be replaced with a new cartridge every 6 to 9 months.

3.Place the filter cartridge back by pushing it upward into its adapter. It is recommended to have a second filter as spare part. Filter cartridges and cleaning solutions are available at your retailer.

Winterizing your Spa.

The Voyager is designed to be operated year round. If you decide not to use your spa during the winter or during an extended period of time, it is recommended to disassemble it and store it in a dry and warm place. Remember to clean and dry the liner as outlined previously.

If you decide to keep and use your spa outside during the winter, keep it at the desired temperature, making sure to keep the cover on. The added "Freeze Protection" safety feature will insure a safe operation.

PAGE 13