Changing the wall station’s security code | Wayne-Dalton 3982

Changing the wall station’s security code:

Step 23: Wall Station Security Code Change and Programming

NOTE: The user must change the wall station’s security code before using the wall station.

This code setting sequence is only required the ﬁrst time the wall station is used.

Overview: When changing the wall station’s security code, the user will have to hold the light button down for approximately 10 seconds, then release the button momentarily, and ﬁnally hold the button down again for approximately 5 seconds.

Changing the wall station’s security code:

1.Press and hold the wall station’s light button for ap- proximately 10 seconds until the wall station’s LED begins to blink rapidly. Once the LED starts blinking release the wall station’s light button; the LED will turn off.

2.Press and hold the wall station’s light button again (LED will light) for approximately 5 seconds. After approximately 5 seconds the LED will begin to blink on and off. Release the light button. The wall station’s LED will blink on and off three times indicating a suc- cessful security code change.

The wall station is now ready to be programmed to the opener.

LIGHT BUTTON

LED

Wall Station Programming

To program wall station:

1.Verify the emergency disconnect handle is in the manual door operated position (lower position). This is for safety reasons.

2.On the front cover of the opener, press and release the red program button; the opener will beep once, indicating activation of the program mode. The opener will remain in program mode for 30 seconds.

3.Press and hold the wall station light button until the opener beeps one time. The wall station is now programmed.

4.Return the emergency disconnect handle to the mo- tor operated position (upper position).

No beeping response of the opener during the wall station programming indicates a programming failure. Repeat programming Steps 1-4.

NOTE: Programming failure can occur during the wall station programming if the remote control is too close to the opener during the programming sequence. Perform the programming with a minimum of six feet between the remote control and the opener.

MOTOR IN UP POSITION

OPENER

RED PROGRAM

BUTTON

LIGHT

HANDLE IN MANUAL OP- BUTTON

ERATED POSITION

24

Image 24

Wayne-Dalton 3982 installation instructions Changing the wall station’s security code, Wall Station Programming

Contents

Important Notice Model 3982 idrive Extension Spring Kit Table of Contents System RequirementsFCC and IC Statement FCC Regulatory Information INSTALLATION AND USE INSTALLATION AND USE Hardware Kit: 3982 idrive Extension Spring Kit idrive Package Contents idrive Hardware Kit Available Accessories: For idrive Tools Needed idrive Retro-ﬁtInstallation Extension idrive InstallationStep 1: Extension Spring Relief Step 2: Remove Front Sheave Step 4: Flag Bracket Installation Step 4A: Track Width ConformationNOTE: In some instances there shown in step Step 5: Cable Drum Installation Step 6 Bottom Bracket Lifting CablesNOTE Do not remove shrink wrap from cable drums until instructed to do so Step 7: Drum Wrap Installation Step 8 Extension Spring Counterbalancewrapped oppositely on the drum Step 9: Safety Cable Installation Step 10 Lower the DoorWARNING TO AVOID SEVERE IN JURY DO NOT PLACE FINGERS OR HAND Step 11: idrive Opener/Torque Tube Assembly NOTE Hold the opener by the mainbody. Do not hold by the motor NOTE: Do not force the opener onto Step 13: Secure idrive Opener Step 14: Disconnect Installation tion be pilot drilled using 1/8” drill bitNOTE: It is recommended that 1/4” lag screw loca and Owner’s Manual Pre-OperationInstallation Step 15: Wall Station Installation Switch Settings Light Fixture Jumper Settings: OpenerStep 16 Multi-Opener/LightFixture Programming Step 17: Light Fixture Installation CEILING MOUNTING Light Fixture Installation Continued power back on at fuse boxWALL MOUNTING Step 18: Photoelectric Safety Sensor Installation NOTE: If wires must be lengthened or spliced intonectors Photoelectric Safety Sensor Installation Continued Step 19: Power Connection Standard Wiring CONVENIENT POWER OUTLETLIGHT FIXTURE POWER OUTLET RECEPTACLE #6 X 7/8 WOOD SCREWS POWER CORD FEMALE END OPENER Step 20 Power Connection Permanent Wiring Option Step 22: Photoelectric Safety Sensor Alignment Step 21 Securing the Opener Changing the wall station’s security code Wall Station Programming Step 24 Install Routine MOTOR OPERATED POSITIONUP/DOWN BUTTON PROFILE BUTTON Step 25: Detent Adjustment if required Step 26: Lock Arm InstallationStep 27: Custom Settings Step 28 Photoelectric Obstruction Sensor Test Step 29: Contact Obstruction Test Step 30: Transmitter Security Code Change and ProgrammingCHANGING THE TRANSMITTER’S SECURITY CODE TRANSMITTER PROGRAMMING Teaching Power Unit Step 31: Programming HomeLink to idriveper Step PROGRAMMING Training HomeLink Unit Important Safety Instructions 8.SAVE THESE INSTRUCTIONSOperation Transmitter Operation service person immediately Wall Station Operation Manual Door Operation Emergency Disconnect MOTOR DOWN POSITION DOOR LOCKEDDISCONNECTED, MOTOR UP POSITION Maintenance Monthly MaintenanceBattery replacement NOTE: Dispose of dead batteries properly Troubleshooting SYMPTOMPROBABLE CAUSE CORRECTIVE ACTION Troubleshooting continued Lock Arm TroubleshootingSYMPTOM SYMPTOM Wayne-DaltonCustomer Service LIFETIME LIMITED WARRANTYQuestions?? For quick answers and helpful advise, call