Tools Needed, Available Accessories: For idrive

Tools Needed:

	1/8” Drill Bit
	3/32” Drill Bit
	Power Drill	Tape Measure
	Power Drill
	Pencil
	7/16” Socket	Step Ladder
	1/2” Socket	Step Ladder
	1/2” Socket	7/16” Wrench
	9/16” Socket	1/2” Wrench
	3/4” Socket	9/16” Wrench
	7/16” Socket Driver	3/4” Wrench
		3/4” Wrench
		Flat Head Screw-
		driver
	Safety Glasses	Phillips Head
		Phillips Head
	3/8” Hex Wrench	Screwdriver

Ratchet	Level	Locking Pliers (2)

Available Accessories: For idrive™

3-Button Mini RF Trans-
mitter
Model no: 3973
Part no: 302083
Keyless Entry RF
Transmitter	Low Headroom Kit
Model no: KEP2	Part no: 302883
Part no: 302078
Infrared Safety Sensor
Model no: ML2
Part no: 301674
Power Cord Extender
Model no: 3960M, Part no: 302616
5-Button Wall-Station RF	Deluxe Wireless Light Kit
Transmitter	Model no: 3950-ULDRE
Model no: 3975	Part no: 302097

Part no: 302090

Page 6

Image 6

Wayne-Dalton 3982 installation instructions Tools Needed, Available Accessories: For idrive

Contents

Important Notice Model 3982 idrive Extension Spring Kit FCC and IC Statement Table of ContentsSystem Requirements FCC Regulatory Information INSTALLATION AND USE INSTALLATION AND USE Hardware Kit: 3982 idrive Extension Spring Kit idrive Package Contents idrive Hardware Kit Available Accessories: For idrive Tools Needed Step 1: Extension Spring Relief idrive Retro-ﬁtInstallationExtension idrive Installation Step 2: Remove Front Sheave NOTE: In some instances there Step 4: Flag Bracket InstallationStep 4A: Track Width Conformation shown in step NOTE Do not remove shrink wrap from cable Step 5: Cable Drum InstallationStep 6 Bottom Bracket Lifting Cables drums until instructed to do so Step 7: Drum Wrap Installation Step 8 Extension Spring Counterbalancewrapped oppositely on the drum WARNING TO AVOID SEVERE IN Step 9: Safety Cable InstallationStep 10 Lower the Door JURY DO NOT PLACE FINGERS OR HAND body. Do not hold by the motor Step 11: idrive Opener/Torque Tube AssemblyNOTE Hold the opener by the main NOTE: Do not force the opener onto Step 13: Secure idrive Opener NOTE: It is recommended that 1/4” lag screw loca Step 14: Disconnect Installationtion be pilot drilled using 1/8” drill bit and Owner’s Manual Pre-OperationInstallation Step 15: Wall Station Installation Switch Settings Light Fixture Jumper Settings: OpenerStep 16 Multi-Opener/LightFixture Programming Step 17: Light Fixture Installation CEILING MOUNTING Light Fixture Installation Continued power back on at fuse boxWALL MOUNTING Step 18: Photoelectric Safety Sensor Installation NOTE: If wires must be lengthened or spliced intonectors Photoelectric Safety Sensor Installation Continued LIGHT FIXTURE POWER OUTLET RECEPTACLE Step 19: Power Connection Standard WiringCONVENIENT POWER OUTLET #6 X 7/8 WOOD SCREWS POWER CORD FEMALE END OPENER Step 20 Power Connection Permanent Wiring Option Step 22: Photoelectric Safety Sensor Alignment Step 21 Securing the Opener Changing the wall station’s security code Wall Station Programming Step 24 Install Routine MOTOR OPERATED POSITIONUP/DOWN BUTTON PROFILE BUTTON Step 25: Detent Adjustment if required Step 26: Lock Arm InstallationStep 27: Custom Settings Step 28 Photoelectric Obstruction Sensor Test Step 29: Contact Obstruction Test CHANGING THE TRANSMITTER’S SECURITY CODE Step 30: Transmitter Security CodeChange and Programming TRANSMITTER PROGRAMMING per Step Teaching Power UnitStep 31: Programming HomeLink to idrive PROGRAMMING Training HomeLink Unit Operation Important Safety Instructions8.SAVE THESE INSTRUCTIONS Transmitter Operation service person immediately Wall Station Operation Manual Door Operation Emergency Disconnect MOTOR DOWN POSITION DOOR LOCKEDDISCONNECTED, MOTOR UP POSITION Battery replacement MaintenanceMonthly Maintenance NOTE: Dispose of dead batteries properly PROBABLE CAUSE TroubleshootingSYMPTOM CORRECTIVE ACTION SYMPTOM Troubleshooting continuedLock Arm Troubleshooting SYMPTOM Questions?? Wayne-DaltonCustomer ServiceLIFETIME LIMITED WARRANTY For quick answers and helpful advise, call