Installation, Tools Needed None | Wayne-Dalton 9800 Series instruction

Installation

IMPORTANT: Read instructions titled “p4” “Removing the old door” on page 9 and “p5” “PREPARING THE OPENING” on page 10 before attempting door installation.

IMPORTANT: Stainless steel or PT 2000 coated lag screws MUST be used when installing center bearing brackets, end brackets, jamb brackets, operator mounting/support brackets and disconnect brackets on treated lumber (preservative-treated). Stainless steel lag screws are NOT necessary when installing products on un-treated lumber.

NOTE: It is recommended that 5/16” x 1-5/8” lag screws be pilot drilled using a 3/16” drill bit, and 1/4” x 2” lag screws and 1/4” x 1- 1/2” lag screws be pilot drilled using a 1/8” drill bit, prior to fastening.

INSTALLATION

1

Tools Needed:

None

Attaching Quick Install Flag

Angle to Vertical Track

NOTE: If you have fully adjustable flagangles, skip this step and complete Step 2.

Place the lower quick install tab of the flagangle in the quick install feature of the vertical track. Give the flagangle 1/4 turn to lock in place. Repeat for other side.

NOTE: After completing this step, continue with Step 3.

QUICK INSTALL TAB UNLOCKED

QUICK INSTALL TAB LOCKED

FLAGANGLE

FLAGANGLE

VERTICAL	VERTICAL
TRACK	TRACK

left hand track and flagangle

right hand track and flagangle

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local 11 yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Image 11

Wayne-Dalton 9800 Series Installation, Attaching Quick Install Flag Angle to Vertical Track, Tools Needed None, Flagangle

Contents

Important Notice Series 4 Section Table of Contents PRE-INSTALLATION Package Contents Door Section Identification Gloves Power DrillTools Required 3/16 Drill Bits Suddenly, resulting in severe Or fatal injury Torsion Spring Removal For Standard LiftFailure to use approved Winding bars can cause spring Energy to be released Unwind Springs Bracket and Drive Gear TorqueMaster SpringRemoval Removing the Old Door Extension Spring Removal Preparing the Opening Flagangle InstallationAttaching Quick Install Flag Angle to Vertical Track Tools Needed None Aside Be installed as shownHorizontal Angle Tap the horizontal angle towards Brackets Installing Q.I. Jamb Brackets Vertical Track Bottom Section Stacking Sections 20 x 5/8 carriage bolts Top BracketsWith the second set of holes from Endcap Operator Bracket Top Section Injury Attaching Horizontal Track toDo not Raise Door Until Hex nuts This step Adjusting Top Brackets Continue with Step Idrive opener on your garage door, you Must install the center bracket bushingTorqueMaster Spring Tube Center Bracket Bushing Idrive Installation Cable Drum Installation Repeat for left hand side.` Drive Gear InstallationEnd Brackets Tools Needed Lubricating Oil Repeat for left hand side for double spring applications Counter InstallationSecuring Center Bracket Assembly Installations on page 35, Figure B Positioning Support Bracket Handle Bracket Attaching Disconnect CablesMounting Disconnect Secure disconnect cable to Disconnect handle. ThreadDisconnect handle Bracket Important do not USE Impact GUN to Wind Springs Cable AdjustmentsTools Needed Vice Clamp Tools Needed Locking Pliers Flat Tip Screwdriver Recommended Spring Turns Setting Spring TensionWinding Bolt Rotation Parallel and within 3/4 Maximum of door edge Drum Wrap InstallationRear Support Keep horizontal track Weather seal or door stop to both door Adjust weather seal or door stop ifAttach horizontal tracks to the rear Tools Needed DoorMaster TM Bracket Side Lock No Scew EYE Pull Rope Bottom Bracket Tools Needed Power Drill Drill BitPull Rope Door is fully open trolley rail will Trolley OperatorOperator Must be Tested AT Time Result in Severe or Fatal Injury Important do not USE a Pressure Washer on Garage Door Cleaning Your Steel And Fiberglass Garage DoorGlass Cleaning Instructions Acrylic Cleaning Instructions Fiberglass Refinishing And Or Finishing Steel Preparation For Painting Thank you for your purchase Lifetime Limited Warranty Model