22 | Positioning Support Bracket |
|
|
|
|
|
|
| |
Tools Needed: | NOTE: See idrive® main installation and | 45 angle | Antenna | |
| owners manual for idrive® parts. |
| wire | |
Power Drill |
|
|
| |
|
|
|
| |
1/8” Drill Bit | NOTE: idrive® must be installed on a |
|
|
|
solid mounting surface. |
|
|
| |
|
|
|
| |
7/16” Socket | Locate the mounting surface. The |
|
|
|
Driver |
|
|
| |
| mounting surface is a vertical board |
|
|
|
| running directly above the center of the |
|
| TorqueMaster® |
| door. Remove (2) |
|
| |
|
|
| spring tube | |
| nuts from bottom of opener. |
|
| |
|
|
| SUPPORT | |
|
|
|
| |
| NOTE: Do not discard flange nuts. |
|
| BRACKET |
| 1/4” X |
|
| |
|
|
|
| |
| Place the support bracket underneath | LAG SCREW |
|
|
| (Header) |
|
| |
| opener, to the right side of motor, | TOP OF DOOR | (2) 1/4” - 20 |
|
| centered on mounting surface. Using a | FLANGE hex |
| |
|
|
| ||
| tape measure, level the bottom of the |
| NUTS |
|
|
|
|
| |
| TorqueMaster® spring tube to the top of |
|
|
|
| the door section with the idrive® resting |
|
|
|
| on the support bracket. Once |
|
| mounting |
| TorqueMaster® spring tube is level, drill |
|
| |
| 1/8” pilot holes for the lag screws. Then |
|
| studs |
|
|
|
| |
| secure support bracket to the mounting |
|
|
|
| surface with (2) 1/4” x |
|
|
|
| screws. |
| mounting |
|
|
|
| bracket | |
|
|
| studs | |
| IMPORTANT: TorqueMaster® spring |
| slots | |
|
|
| ||
| tube must be level after support |
|
|
|
| bracket is fastened to mounting |
|
|
|
| surface. |
|
|
|
| NOTE: If wood mounting surface is |
|
| support |
| TorqueMaster® |
| bracket | |
| behind dry wall, use 1/4” x 2” lag | spring tube |
|
|
| screws. |
|
|
|
| Lift and slide the opener over the |
|
|
|
| support bracket, aligning the mounting |
|
|
|
| studs with the bracket slots. Loosely |
|
| (2) 1/4” - 20 |
| fasten to mounting studs with the (2) |
|
| |
|
|
| flange hex | |
|
|
| ||
|
|
| nuts | |
| NOTE: Do not tighten |
|
|
|
| hex nuts to opener studs at this time. |
|
|
|
| Remove the temporary orange label | “x” | “x” | “x” |
| holding the antenna wire. Straighten |
|
|
|
| antenna wire and angle it 45 degrees to |
|
|
|
| the right. |
|
|
|
| NOTE: Do not coil the antenna wire. |
| top section |
|
| This will reduce the radio signal range. |
|
|
|
|
| Using a tape measure, maintain an equal measurement “x” | ||
|
| (top of door to bottom of Torquemaster® tube) at both | ||
|
| ends and the center. |
| |
26 Please Do Not Return This Product To The Store. Contact your local
