| Rear Support Continued... |
|
|
| horizontal tracks to the rear supports with | Sound Framing Members |
|
Tools Needed: |
|
| |
|
| ||
|
|
| |
| not be supplied). Horizontal tracks must be |
|
|
| level and parallel with door. |
|
|
| NOTE: If rear supports are to be installed |
|
|
| over drywall, use 5/16” x 2” hex head lag |
| perforated ANGLE |
| screws. | angle | |
| - BOLTED USING (2) 5/16” | ||
| NOTE: If an idrive® opener is installed, | ||
| brace | ||
| position horizontal tracks one hole above |
| X |
|
| SCREWS TO CEILING | |
| level when securing it to rear supports. |
| |
| Adjust weather seal or door stop (if |
| MEMBER AND PARALLEL |
| necessary). Now permanently attach the |
| TO DOOR |
| weather seal or door stop to both door |
|
|
| jambs and header. (They were temporarily | HORIZONTAL TRACK | BOLT MUST EXTEND INTO |
| attached in PREPARING THE OPENING on |
| THE TRACK TO SERVE AS |
| page 10.) Avoid pushing weather seal or |
| A ROLLER STOP |
| door stop too tightly against face of door. |
| |
|
|
| |
| WARNING | Sound Framing Members |
|
| Prior to winding or making |
|
|
| adjustments to the springs, |
|
|
| ensure you’re winding in the |
|
|
| proper direction as stated in the |
|
|
| Installation Instructions. Otherwise |
| perforated ANGLE - |
| the spring fittings may release from | angle | BOLTED USING (2) 5/16” |
| spring if not wound in the proper | ||
| brace | X | |
| direction and could result in severe | ||
|
| SCREWS TO CEILING | |
| or fatal injury. |
| |
|
| MEMBER AND PARALLEL | |
|
|
| |
| Now, lift door and check it’s balance. |
| TO DOOR |
| Adjust, if door lifts by itself (hard to pull | HORIZONTAL TRACK |
|
| down) or if door is difficult to lift (easy to | BOLT MUST EXTEND INTO | |
| pull down). Anytime spring adjustments are |
| THE TRACK TO SERVE AS |
| made you must loosen the lock nuts before |
| A ROLLER STOP |
| beginning adjustments. Retighten both lock | PERFORATED ANGLE |
|
| nuts after completion. To adjust spring(s), |
| |
| only add or remove 1/4 turn on the counter |
|
|
| at a time. Adjust both sides equally. |
|
|
| IMPORTANT: Do not add or remove |
|
|
| more than 1 spring turn from |
| weather |
| specified amount. If the door still |
| |
|
| seal | |
| does not operate easily, lower the |
| |
|
|
| |
| door to the closed position, UNWIND |
|
|
| SPRING(S) TO ZERO, and recheck the |
|
|
| following items: |
| jamb |
| 1.) Check the door for level. |
| |
|
|
| |
| 2.) Check the TorqueMaster® spring tube | (3) 5/16” |
|
| and flagangles for level and plumb. | BOLTS & NUTS | permanently attached |
| 3.) Check the distance between the | ||
|
| weather seal | |
| flagangles - must be door width |
| |
|
|
| |
| plus |
|
|
| 4.) Check the counterbalance cables |
|
|
| for equal tension - adjust if necessary. |
|
|
| 5.) Rewind the spring(s). |
|
|
| 6.) Make sure door isn’t rubbing on jambs. |
|
|
NOTE: As a safety feature, the right hand end bracket cannot be disassembled for service until the spring is completely unwound and the counter cover reads zero. After door installation is completed, refer to the idrive® owner’s manual to complete the idrive® installation.
32 Please Do Not Return This Product To The Store. Contact your local