Operating Instructions and Parts Manual

Shallow Well Jet Pump

Manual de instrucciones de operación y piezasModelos para pozos profundos

General Safety Information (Continued)

16.Do not attempt repairs to the electric motor. All repairs to the motor must be completed at a licensed or certified electrical motor repair shop.

Do not touch an

! WARNING operating motor. Modern motors are designed to operate at high temperatures.

17.Avoid kinking electrical cord and protect from sharp objects, hot surfaces, oil and chemicals. Replace or repair damaged or worn cords immediately.

Disconnect power

! WARNING and release all pressure from the system before attempting to install, service, relocate or perform any maintenance. Lock the power disconnect in the open position. Tag the power disconnect to prevent unexpected application of power.

18.Keep fingers and foreign objects away from ventilation and other openings. Do not insert any objects into the motor.

Risk of electric ! WARNING shock! Never

connect the green (or green and yellow wire) to a live terminal!

19.To reduce the risk of electrical shock, the pump should be plugged directly into a properly installed and grounded 3-prong grounding type receptacle, as shown in Figure 1. The green (or green and yellow) conductor in the cord is the grounding wire. The motor must be securely and adequately grounded for protection against shock.

Grounded

Pin

TESTRESET

Figure 1

Grounded Outlet

21.Use only 3-wire extension cords that have a 3-prong, grounding type plug, and 3-pole receptacles that accept the equipment plug.

22.Use wire of adequate size to minimize voltage drop at the motor.

Do not handle ! DANGER pump or pump

motor with wet hands, when standing on a wet or damp surface or when standing in water. Fatal electrical shock could occur.

Pump motor is

! WARNING equipped with an automatic resetting thermal protector and may restart unexpectedly. Protector tripping is an indication of motor overloading because of operating pump at low heads (low discharge restriction), excessively high or low voltage, inadequate wiring, incorrect motor connections or defective motor or pump.

Pre-Installation

WATER SUPPLIES

The water supplies illustrated in Figure 12 are possible sources for water. These water supplies can be divided into two categories:

SURFACE WATER

Water from a lake, stream, pond and cistern. This water is usually not fit for human consumption, but may be suitable for washing, irrigation or other household uses.

GROUND WATER

Water found in the water bearing stratum at various levels beneath the earth. Of all the fresh water found on earth only 3 percent is found on the surface and 97 percent is underground.

TANKS - CONVENTIONAL STORAGE

The function of the tank is to store a quantity of water under pressure. When full, the tank contains approximately 2/3 water and 1/3

compressed air. The compressed air forces the water out of the tank when a faucet is opened. An air volume control automatically replaces air lost or absorbed into the water. The usable water, or drawdown capacity, of the tank is approximately 1/6 of the tanks total volume when operated on a “20- 40” pressure setting (Figure 2).

TANKS - PRECHARGED STORAGE

 

Air Volume

 

Control

 

Bladder

Conventional

Precharged

Tank

Tank

Figure 2 - Conventional & Precharged

Storage Tanks

A precharged storage tank has a flexible bladder or diaphragm that acts as a barrier between the compressed air and water. This barrier prevents the air from being absorbed into the water and allows the water to be acted on by compressed air at initially higher than atmospheric pressures (precharged). More usable water is provided than with a conventional type tank. Precharged tanks are specified in terms of a conventional tank. For example, a 20 gallon precharged tank will have the same usable water or drawdown capacity as a 40 gallon conventional tank, but the tank is smaller in size (Figure 2).

PRESSURE SWITCH

The pressure switch provides for automatic operation. The pump starts when pressure drops to a cut-in setting.

Para Piezas de Repuestos, Llame al 1-800-237-0987

Sírvase proporcionar la suguiente información:

Puede escribirnos a:

 

 

- Número de modelo

Wayne Water Systems

 

 

- Número de serie (si tiene)

101 Production Drive

 

 

- Descripción y número de repuesto como se muestra

Harrison, OH 45030 U.S.A.

 

 

en la lista de repuestos

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

6

7

 

 

12

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

9

8

 

 

 

 

 

 

 

10

11

13

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16

 

 

 

 

 

 

 

 

17

 

 

 

14

 

 

 

 

 

 

 

 

 

 

 

 

 

15

 

No. de

 

Para Los Modelos

 

 

Ref.

 

Descripción

SWS50-1/2 HP

SWS75-3/4 HP

SWS100-1 HP

Ctd.

1

 

Motor

32059-001

34142-001

34142-001

1

2

 

Tornillo

16636-002

16636-002

16636-002

4

3

 

Placa de sellado

4372-001

4372-001

4372-001

1

4

•

Empaquetadura cuadrada de caucho para anillo

17150-001

17150-001

17150-001

1

5

•

Ensamblaje de sello del eje

56393

56393

 

56393

1

6

 

Impulsor

23285-021

23285-022

23285-022

1

7

 

Difusor

17148-021

17148-021

17148-021

1

8

 

Tornillo

67007-001

67007-001

67007-001

2

9

•

Anillo en o

15557

15557

 

15557

1

10

 

Venturi

17151-002

17151-003

17151-004

1

11

 

Boquilla

15672

15672

 

15672

1

12

 

19,1 mm (3/4”) Tapón de cebado

15921

15921

 

15921

1

13

 

Voluta

56869-001

56869-001

56869-001

1

14

 

6,4 mm (1/4”) NPT Tapón de cebado

16314-002

16314-002

16314-002

1

15

 

3,2 mm (1/8”) NPT Tapón de cebado

15766-002

15766-002

15766-002

1

20.Where a 2-prong is encountered, replace the plug with a properly grounded 3-prong receptacle in accordance with the National Electrical Code, local codes and ordinances. To ensure a proper ground, the grounding means must be tested by a licensed or certified electrician.

CHART 1 - JET PUMP/TANK ASSEMBLIES

 

 

 

Air Volume

 

 

 

Control

 

 

Type

Required

 

 

 

 

 

 

Well X

Precharged

No

 

 

 

 

 

 

PCA

Precharged

No

 

 

 

 

 

 

 

12P & 30P Horizontal

Conventional

Yes

 

 

 

 

 

 

 

FX Horizontal

Precharged

No

 

 

 

 

 

 

17

Base

23029-021

23029-021

23029-021

1

19

Presostato

30010-021

30010-021

30010-021

1

•

Juego para reparaciones (Incluyes #4, 5 y 9)

56874-001

56874-001

56874-001

1

www.waynewatersystems.com

2

31 Sp