Configuration Examples | Weed Eater 2600 guide

Cisco High-Density Analog Voice and Fax Network Module

Configuration Examples

Configuration Examples

This section provides the following voice port configuration examples:

•Analog FXO Voice Port Example

•Analog FXS Voice Port Example

Analog FXO Voice Port Example

The following example shows analog FXO output for voice-port configuration:

voice-port 1/0/4 no vad

timeouts call-disconnect 3 timeouts wait-release 3 connection trunk 8004 answer-mode supervisory disconnect dualtone pre-connect supervisory answer dualtone

no battery-reversal

!

voice-port 1/0/5 no vad

timeouts call-disconnect 3 timeouts wait-release 3 connection trunk 8005 answer-mode supervisory disconnect dualtone pre-connect supervisory answer dualtone

no battery-reversal

!

voice-port 1/0/6 no vad

timeouts call-disconnect 3 timeouts wait-release 3 connection trunk 8006 answer-mode supervisory disconnect dualtone pre-connect supervisory answer dualtone

no battery-reversal

!

voice-port 1/0/7 no vad

timeouts call-disconnect 3 timeouts wait-release 3 connection trunk 8007 answer-mode supervisory disconnect dualtone pre-connect supervisory answer dualtone

no battery-reversal

!

Cisco IOS Release 12.2(2)XT and 12.2(8)T

29

Image 29

Weed Eater 2600 manual Configuration Examples, Analog FXO Voice Port Example

Contents

Cisco High-Density Analog Voice and Fax Network Module Feature History Release Modification Base Module Feature OverviewVoice Port Numbers Interface FXS and FXO Interfaces Telephony Signaling Interfaces Disconnect Supervision Commands Delay in Voice Networks FXO Supervisory Disconnect Tone Commands Adaptive Jitter Buffering Voice Level AdjustmentEcho Cancellation Serviceability Voice Activity Detection CommandsBenefits Cost Effective Supported High-Complexity Codecs RestrictionsSupported Medium-Complexity Codecs Supported low-Complexity Codecs Cisco 2600 series Supported PlatformsRelated Documents Prerequisites Supported Standards, MIBs, and RFCs Configuring Analog FXO and FXS Voice Ports Configuration TasksCommand Purpose FXO or FXS Default is Keyword default is 25 on Cisco 2600 seriesDefault is the pattern specified by the cptone Locale that has been configured Fine-Tuning Analog Voice Ports Configuring Voice Activity Detection VAD Configuring Disconnect Supervision Commands Reversal is enabled Enables battery reversal. The default is that batteryFor FXO ports-Use the no battery-reversal Command to configure a loop-start voice port to not Configuring FXO Supervisory Disconnect Tone Commands Sec. The default is From 0 to 1000 0 ms to 10 sec. The default isExits voice class configuration mode Voice network module is installed Configuring Timeouts Commands Timing Commands Configuring Adaptive Jitter Adjustment Voice Quality Tuning Commands Configuring Voice Level Adjustment Configuring Echo Adjustment Platform Command Syntax Verifying Analog Voice-Port Configurations Troubleshooting Chart, Voice Port Testing Commands, Troubleshooting Tips Problem Suggested Action Troubleshooting ChartReconfigure the voice port Keyword setting also called region tone is US Configuring Voice Level Adjustment section on Voice Port Testing Commands Loopback Function Tests Detector-Related Function Tests Relay-Related Function Tests Tone Injection Tests Keyword fax to force the voice port into fax mode Fax/Voice Mode TestsTest. Enter the keyword disable to return Voice port to voice mode Analog FXO Voice Port Example Configuration Examples Analog FXS Voice Port Example Debug dspapi, Debug hpi, Command Reference Debug dspapi Defaults Command Modes Command HistorySyntax Description Release Modification Related Commands Description Command Modes Command History DefaultsDebug hpi Usage Guidelines Examples To global configuration mode Global configurationVoice-port Cisco 2600, and Cisco 3600 Router Encapsulation Dial-peer voice Glossary