Questions?, Customer HOT Line | Weider WESY59101 instruction

Model No. WESY59101

Serial No.

Write the serial number in the space above for future reference.

Serial Number Decal (Under Seat)

QUESTIONS?

As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if there are missing parts, we will guarantee complete satisfaction through assistance from our factory.

TO AVOID DELAYS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUSTOMER

HOT LINE. The techni- cians on our customer hot line will provide immediate assistance, free of charge.

CUSTOMER HOT LINE:

1-800-999-3756

Mon.–Fri., 6 a.m.–6 p.m. MST

CAUTION

Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference.

USER'S MANUAL

Visit our website at

www.weiderfitness.com

new products, prizes, fitness tips, and much more!

Image 1

Weider user manual Questions?, Model No. WESY59101 Serial No, Serial Number Decal Under Seat, Customer HOT Line

Contents

Model No. WESY59101 Serial No QUESTIONS?Serial Number Decal Under Seat Customer HOT Line Limited Warranty Table of Contents Replacement decal Apply the decal in the location shown Important PrecautionsMake sure all parts are properly tightened Ing down Decal shown Before YOU Begin Using the weight systemFor your benefit, read this manual carefully before Decal Cable Assembly AssemblyArm Assembly To open the parts bag for that stage Assembly Frame Assembly Do not tighten the Nylon Locknuts yet See the inset drawing Press the Weight Tube Bumper 18 into the Weight TubeCorner bar of the Press Base Slot Locknuts 50. Do not tighten the Nylon Locknuts yet ARM AssemblyTighten the Nylon Locknuts used in steps Handles Bolt and a 3/8 Nylon Locknut Able to pivot easily Cable AssemblyInsert two 2 Square Inner Caps 28 into the Leg Lever 101 Hold the Cable in place Trap is turned to hold the Cable in place Plates 23 with a 3/8 x 2 Bolt 54 and a 3/8 Frame 9. Attach a 3/8 Flat Washer 48 and aNylon Locknut Wrap the Ab Pulley 47 around another 3 1/2 Be sure Weight Cable is in the groove of the 3 1/2 Pulley Weight Cable has a bolt, and the other End has a ball on it Cable Trap is turned to hold the Cable in place Wrap the Weight Cable 72 around a 3 1/2 Pulley4 Bolt 57 and a 3/8 Nylon Jamnut Cable in place Remove the preassembled 3/8 x 1 3/4 Bolts Be sure that Cable Trap is turned to hold the Cable in place Do not tighten the Nylon Locknut yet Be sure To hold the Cable in placePlace Hold the Cable 75 in place Locate and open the parts bag labeled Seat Assembly Seat Assembly Maintenance on ADJUSTMENTS, beginning on page 21 of this manualWelded Attaching the LAT BAR or AB Strap to High Pulley Station AdjustmentsAb Strap 81 can be attached in the same manner Attaching the LAT BAR, AB STRAP, or Nylon Adjusting the Curl PAD Adjusting the BackrestAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart Tightening the Cables Troubleshooting and MaintenanceRetighten the 1/2 Plain Nut down onto the 1/2 Flat Washer Right Arm Cable Diagrams Weight Cable Cable ID Stack Page Part No R0103A Ordering Replacement Parts For That Assembly Stage Pulley 27 Not shown to scale 2 Pulley 24 Not shown to scale R0103A X 3 1/4 Bolt 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Key Exploded