ARM Assembly | Weider WESY59101 guide

12. Secure the Press Top Frame (9) to the Butterfly Top

Frame (33) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat Washers (48), and two 3/8” Nylon

Locknuts (50). Do not tighten the Nylon Locknuts yet.

13. Secure the Weight Guides (15) to the Press Top

Frame (9) with two 3/8” x 1 3/4” Bolts (57) and two 3/8” Nylon Locknuts (50).

Tighten the Nylon Locknuts used in steps 2–13.

ARM ASSEMBLY

14.Locate and open the parts bag labeled “ARM ASSEMBLY.”

Press a 1 1/2” Square Inner Cap (35) into the Right Pivot Arm (85).

Lubricate the axles on the Butterfly Top Frame (33). Secure the Right Pivot Arm (85) to the right axle with two Retainer Rings (31) and a 1” Round Outer Cap (38). Do not confuse the Right Pivot Arm with the Left Pivot Arm (not shown). The Retainer Rings may break if disassembled.

Note: Be sure the Retainer Rings (31) and 1” Round Outer Cap (38) are oriented as shown in the inset drawing.

Repeat this step with the Left Pivot Arm (not shown) and left axle.

12
	50	62
	48	62
	9	48
		48
		33
13	57
	57
	9
	50	50
		50
	15
14
		33
		Lubricate
		85
	35	31
	Axle	38
	Axle
31
	38

9

Image 9

Weider WESY59101 user manual ARM Assembly, Locknuts 50. Do not tighten the Nylon Locknuts yet

Contents

Model No. WESY59101 Serial No QUESTIONS?Serial Number Decal Under Seat Customer HOT Line Limited Warranty Table of Contents Replacement decal Apply the decal in the location shown Important PrecautionsMake sure all parts are properly tightened Ing down Decal shown Before YOU Begin Using the weight systemFor your benefit, read this manual carefully before Decal Cable Assembly AssemblyArm Assembly To open the parts bag for that stage Assembly Frame Assembly Do not tighten the Nylon Locknuts yet See the inset drawing Press the Weight Tube Bumper 18 into the Weight TubeCorner bar of the Press Base Slot ARM Assembly Locknuts 50. Do not tighten the Nylon Locknuts yetTighten the Nylon Locknuts used in steps Handles Bolt and a 3/8 Nylon Locknut Able to pivot easily Cable AssemblyInsert two 2 Square Inner Caps 28 into the Leg Lever 101 Hold the Cable in place Trap is turned to hold the Cable in place Plates 23 with a 3/8 x 2 Bolt 54 and a 3/8 Frame 9. Attach a 3/8 Flat Washer 48 and aNylon Locknut Wrap the Ab Pulley 47 around another 3 1/2 Be sure Weight Cable is in the groove of the 3 1/2 Pulley Weight Cable has a bolt, and the other End has a ball on it Cable Trap is turned to hold the Cable in place Wrap the Weight Cable 72 around a 3 1/2 Pulley4 Bolt 57 and a 3/8 Nylon Jamnut Cable in place Remove the preassembled 3/8 x 1 3/4 Bolts Be sure that Cable Trap is turned to hold the Cable in place Do not tighten the Nylon Locknut yet Be sure To hold the Cable in placePlace Hold the Cable 75 in place Locate and open the parts bag labeled Seat Assembly Seat Assembly ADJUSTMENTS, beginning on page 21 of this manual Maintenance onWelded Attaching the LAT BAR or AB Strap to High Pulley Station AdjustmentsAb Strap 81 can be attached in the same manner Attaching the LAT BAR, AB STRAP, or Nylon Adjusting the Backrest Adjusting the Curl PADAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart Troubleshooting and Maintenance Tightening the CablesRetighten the 1/2 Plain Nut down onto the 1/2 Flat Washer Right Arm Cable Diagrams Weight Cable Cable ID Stack Page Part No R0103A Ordering Replacement Parts For That Assembly Stage Pulley 27 Not shown to scale 2 Pulley 24 Not shown to scale R0103A X 3 1/4 Bolt 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Key Exploded