Bolt and a 3/8 Nylon Locknut, Handles | Weider WESY59101 manual

15.Insert a 2” Square Inner Cap (28) into the end of the Butterfly Arm (10).

Attach a Butterfly Handle (53) to the Butterfly Arm

(10)with two 3/8” x 1” Bolts (84) and two 3/8” Flat Washers (48).

Repeat this step with the other Butterfly Arm (10).

16.Lubricate a 3/8” x 3 1/4” Bolt (62). Attach the left Butterfly Arm (10) to the Left Pivot Arm (71) with

the Bolt and a 3/8” Nylon Locknut (50).

Repeat this step with the right Butterfly Arm (not shown) and the Right Pivot Arm (85).

17.Lubricate a 1/2” x 4” Bolt (68). Attach the Press Frame (8) to the Press Base (6) with the Bolt and a

1/2” Nylon Jamnut (36). Note: Do not over tighten the 1/2” Nylon Jamnut (36); the Press Frame (8) must be able to pivot easily.

18.Insert a 2” Square Inner Cap (28) into the top of a Press Arm (77). Press two 1” Round Inner Caps

(86)into the outside ends of the handles.

Attach the Press Arm (77) to the Press Frame (8)

with two 5/16” x 2 3/4” Bolts (96) and two 5/16” Nylon Locknuts (64).

Repeat this step with the other Press Arm (77).

10

	15
		10
	48	48
	48	53
	10	53
	53	84
	53
	48	28
	48	48
	28
	16	50
		50
		10
	85	71
	85	62
		62
		Lubricate
	17
	8
	68
		6
		36
	Lubricate
	18	28
	Handles	86
		86
		64
	96	77
	8

Image 10

Weider WESY59101 user manual Bolt and a 3/8 Nylon Locknut, Handles

Contents

Serial Number Decal Under Seat QUESTIONS?Model No. WESY59101 Serial No Customer HOT Line Table of Contents Limited Warranty Make sure all parts are properly tightened Important PrecautionsReplacement decal Apply the decal in the location shown Ing down Decal shown For your benefit, read this manual carefully before Using the weight systemBefore YOU Begin Decal Arm Assembly AssemblyCable Assembly To open the parts bag for that stage Frame Assembly Assembly Do not tighten the Nylon Locknuts yet Corner bar of the Press Base Press the Weight Tube Bumper 18 into the Weight TubeSee the inset drawing Slot Locknuts 50. Do not tighten the Nylon Locknuts yet ARM AssemblyTighten the Nylon Locknuts used in steps Bolt and a 3/8 Nylon Locknut Handles Insert two 2 Square Inner Caps 28 into the Leg Lever Cable AssemblyAble to pivot easily 101 Trap is turned to hold the Cable in place Hold the Cable in place Nylon Locknut Frame 9. Attach a 3/8 Flat Washer 48 and aPlates 23 with a 3/8 x 2 Bolt 54 and a 3/8 Wrap the Ab Pulley 47 around another 3 1/2 Weight Cable has a bolt, and the other End has a ball on it Be sure Weight Cable is in the groove of the 3 1/2 Pulley 4 Bolt 57 and a 3/8 Nylon Jamnut Wrap the Weight Cable 72 around a 3 1/2 PulleyCable Trap is turned to hold the Cable in place Cable in place Be sure that Cable Trap is turned to hold the Cable in place Remove the preassembled 3/8 x 1 3/4 Bolts Do not tighten the Nylon Locknut yet Place To hold the Cable in placeBe sure Hold the Cable 75 in place Seat Assembly Locate and open the parts bag labeled Seat Assembly Maintenance on ADJUSTMENTS, beginning on page 21 of this manualWelded Ab Strap 81 can be attached in the same manner AdjustmentsAttaching the LAT BAR or AB Strap to High Pulley Station Attaching the LAT BAR, AB STRAP, or Nylon Adjusting the Curl PAD Adjusting the BackrestAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart Tightening the Cables Troubleshooting and MaintenanceRetighten the 1/2 Plain Nut down onto the 1/2 Flat Washer Cable Diagrams Right Arm Weight Cable Cable ID Stack Page Ordering Replacement Parts Part No R0103A For That Assembly Stage R0103A Pulley 27 Not shown to scale 2 Pulley 24 Not shown to scale X 3 1/4 Bolt 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Key Qty Exploded