Do not tighten the Nylon Locknuts yet | Weider WESY59101 specification

5. Attach the Butterfly Seat Frame (14) to the Butterfly

Upright (1) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat Washers (48), and two 3/8” Nylon Locknuts

(50).

Attach the Butterfly Seat Frame (14) to the Butterfly

Front Leg (3) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat Washers (48) and two 3/8” Nylon Locknuts (50).

Do not tighten the Nylon Locknuts yet.

6.Press a 2 1/2” Square Inner Cap (76) into the Press Front Leg (20).

Attach the Press Front Leg (20) to the indicated

3/8” x 2” Carriage Bolts (92) on the Press Base (6)

with two 3/8” Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet. Make sure that the

Press Front Leg is turned so that the indicated hole is on the side shown.

7. Attach the Press Seat Frame (7) to the Press

Upright (2) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat Washers (48), and two 3/8” Nylon Locknuts

(50).

Attach the Press Seat Frame (7) to the Press Front

Leg (20) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat Washers (48), and two 3/8” Nylon Locknuts

(50).

Do not tighten the Nylon Locknuts yet.

8.Insert three 1 1/2” x 2 1/2” Inner Caps (83) into the ends of the Butterfly Top Frame (33).

Attach the Butterfly Top Frame (33) to the Butterfly

Upright (1) with two 3/8” x 2 1/2” Bolts (87), a Support Plate (94), and two 3/8” Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet.

7

5		50
		50
62	1
			50
48	50	14	50
			50
			48
			3
			62
6
	76
Hole
	20	50
		50
	50
			6
		92
7		50
		50
	50	7	48
	50		48
			62
			50
	50		48
	50		2
			2
48
	20
62
	48
8		33	87
		33

	83		83
	83		94
			94
		83
		50
		1	50

Image 7

Weider WESY59101 user manual Do not tighten the Nylon Locknuts yet

Contents

Customer HOT Line QUESTIONS?Model No. WESY59101 Serial No Serial Number Decal Under Seat Limited Warranty Table of Contents Ing down Decal shown Important PrecautionsReplacement decal Apply the decal in the location shown Make sure all parts are properly tightened Decal Using the weight systemBefore YOU Begin For your benefit, read this manual carefully before To open the parts bag for that stage AssemblyCable Assembly Arm Assembly Assembly Frame Assembly Do not tighten the Nylon Locknuts yet Slot Press the Weight Tube Bumper 18 into the Weight TubeSee the inset drawing Corner bar of the Press Base Locknuts 50. Do not tighten the Nylon Locknuts yet ARM AssemblyTighten the Nylon Locknuts used in steps Handles Bolt and a 3/8 Nylon Locknut 101 Cable AssemblyAble to pivot easily Insert two 2 Square Inner Caps 28 into the Leg Lever Hold the Cable in place Trap is turned to hold the Cable in place Wrap the Ab Pulley 47 around another 3 1/2 Frame 9. Attach a 3/8 Flat Washer 48 and aPlates 23 with a 3/8 x 2 Bolt 54 and a 3/8 Nylon Locknut Be sure Weight Cable is in the groove of the 3 1/2 Pulley Weight Cable has a bolt, and the other End has a ball on it Cable in place Wrap the Weight Cable 72 around a 3 1/2 PulleyCable Trap is turned to hold the Cable in place 4 Bolt 57 and a 3/8 Nylon Jamnut Remove the preassembled 3/8 x 1 3/4 Bolts Be sure that Cable Trap is turned to hold the Cable in place Do not tighten the Nylon Locknut yet Hold the Cable 75 in place To hold the Cable in placeBe sure Place Locate and open the parts bag labeled Seat Assembly Seat Assembly Maintenance on ADJUSTMENTS, beginning on page 21 of this manualWelded Attaching the LAT BAR, AB STRAP, or Nylon AdjustmentsAttaching the LAT BAR or AB Strap to High Pulley Station Ab Strap 81 can be attached in the same manner Adjusting the Curl PAD Adjusting the BackrestAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart Tightening the Cables Troubleshooting and MaintenanceRetighten the 1/2 Plain Nut down onto the 1/2 Flat Washer Right Arm Cable Diagrams Weight Cable Cable ID Stack Page Part No R0103A Ordering Replacement Parts For That Assembly Stage Pulley 27 Not shown to scale 2 Pulley 24 Not shown to scale R0103A X 3 1/4 Bolt 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Key Exploded