Manuals
/
Weider
/
Fitness & Sports
/
Home Gym
Weider
WESY59101
user manual
Weight Cable Cable ID Stack
Models:
WESY59101
1
26
35
35
Download
35 pages
28.85 Kb
23
24
25
26
27
28
29
30
<
>
Weight Resistance Chart
Maintenance
Assembly
Adjustments
Weight
Ordering Replacement Parts
Important Precautions
Page 26
Image 26
Weight Cable (72)
11
Cable ID
9
10
6
12—Weight
Stack
72
47
75
73
8
7
5
3
4
1—Low
Pulley
2
26
Page 25
Page 27
Page 26
Image 26
Page 25
Page 27
Contents
Serial Number Decal Under Seat
QUESTIONS?
Model No. WESY59101 Serial No
Customer HOT Line
Table of Contents
Limited Warranty
Make sure all parts are properly tightened
Important Precautions
Replacement decal Apply the decal in the location shown
Ing down Decal shown
For your benefit, read this manual carefully before
Using the weight system
Before YOU Begin
Decal
Arm Assembly
Assembly
Cable Assembly
To open the parts bag for that stage
Frame Assembly
Assembly
Do not tighten the Nylon Locknuts yet
Corner bar of the Press Base
Press the Weight Tube Bumper 18 into the Weight Tube
See the inset drawing
Slot
Tighten the Nylon Locknuts used in steps
ARM Assembly
Locknuts 50. Do not tighten the Nylon Locknuts yet
Bolt and a 3/8 Nylon Locknut
Handles
Insert two 2 Square Inner Caps 28 into the Leg Lever
Cable Assembly
Able to pivot easily
101
Trap is turned to hold the Cable in place
Hold the Cable in place
Nylon Locknut
Frame 9. Attach a 3/8 Flat Washer 48 and a
Plates 23 with a 3/8 x 2 Bolt 54 and a 3/8
Wrap the Ab Pulley 47 around another 3 1/2
Weight Cable has a bolt, and the other End has a ball on it
Be sure Weight Cable is in the groove of the 3 1/2 Pulley
4 Bolt 57 and a 3/8 Nylon Jamnut
Wrap the Weight Cable 72 around a 3 1/2 Pulley
Cable Trap is turned to hold the Cable in place
Cable in place
Be sure that Cable Trap is turned to hold the Cable in place
Remove the preassembled 3/8 x 1 3/4 Bolts
Do not tighten the Nylon Locknut yet
Place
To hold the Cable in place
Be sure
Hold the Cable 75 in place
Seat Assembly
Locate and open the parts bag labeled Seat Assembly
Welded
ADJUSTMENTS, beginning on page 21 of this manual
Maintenance on
Ab Strap 81 can be attached in the same manner
Adjustments
Attaching the LAT BAR or AB Strap to High Pulley Station
Attaching the LAT BAR, AB STRAP, or Nylon
Attaching the AB Strap to the AB Pulley Station
Adjusting the Backrest
Adjusting the Curl PAD
Weight Resistance Chart
Retighten the 1/2 Plain Nut down onto the 1/2 Flat Washer
Troubleshooting and Maintenance
Tightening the Cables
Cable Diagrams
Right Arm
Weight Cable Cable ID Stack
Page
Ordering Replacement Parts
Part No R0103A
For That Assembly Stage
R0103A
Pulley 27 Not shown to scale 2 Pulley 24 Not shown to scale
X 3 1/4 Bolt
2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap
Save this Part LIST/EXPLODED Drawing for Future Reference
Key
Qty
Exploded
Top
Page
Image
Contents