Cable Diagrams, Right Arm | Weider WESY59101 manual

CABLE DIAGRAMS

The cable diagrams on this page and the next page show the proper routing of the Leg Press Cable (75), the Ab Cable (47), the Butterfly Cable (73), and the Weight Cable (72). Use the diagrams to be sure that the Cables have been assembled correctly. The starting and ending points of each Cable have been labeled. The numbers

show the proper route for each Cable.IMPORTANT: If the Cables have not been correctly routed, the weight system will not function properly and damage may occur.

Leg Press Cable (75)

6

9

10

11—Press Upright

75

3

	2
8	1—Press Upright
	1—Press Upright

4
Ab Cable (47)	Butterfly Cable (73)
	2
	4
4	5—Left Arm
5
1—High Pulley
	2
	1—Right Arm
	3
6—Ab Pulley	3
	3

25

Image 25

Weider WESY59101 user manual Cable Diagrams, Right Arm

Contents

Model No. WESY59101 Serial No QUESTIONS?Serial Number Decal Under Seat Customer HOT Line Limited Warranty Table of Contents Replacement decal Apply the decal in the location shown Important PrecautionsMake sure all parts are properly tightened Ing down Decal shown Before YOU Begin Using the weight systemFor your benefit, read this manual carefully before Decal Cable Assembly AssemblyArm Assembly To open the parts bag for that stage Assembly Frame Assembly Do not tighten the Nylon Locknuts yet See the inset drawing Press the Weight Tube Bumper 18 into the Weight TubeCorner bar of the Press Base Slot Locknuts 50. Do not tighten the Nylon Locknuts yet ARM AssemblyTighten the Nylon Locknuts used in steps Handles Bolt and a 3/8 Nylon Locknut Able to pivot easily Cable AssemblyInsert two 2 Square Inner Caps 28 into the Leg Lever 101 Hold the Cable in place Trap is turned to hold the Cable in place Plates 23 with a 3/8 x 2 Bolt 54 and a 3/8 Frame 9. Attach a 3/8 Flat Washer 48 and aNylon Locknut Wrap the Ab Pulley 47 around another 3 1/2 Be sure Weight Cable is in the groove of the 3 1/2 Pulley Weight Cable has a bolt, and the other End has a ball on it Cable Trap is turned to hold the Cable in place Wrap the Weight Cable 72 around a 3 1/2 Pulley4 Bolt 57 and a 3/8 Nylon Jamnut Cable in place Remove the preassembled 3/8 x 1 3/4 Bolts Be sure that Cable Trap is turned to hold the Cable in place Do not tighten the Nylon Locknut yet Be sure To hold the Cable in placePlace Hold the Cable 75 in place Locate and open the parts bag labeled Seat Assembly Seat Assembly Maintenance on ADJUSTMENTS, beginning on page 21 of this manualWelded Attaching the LAT BAR or AB Strap to High Pulley Station AdjustmentsAb Strap 81 can be attached in the same manner Attaching the LAT BAR, AB STRAP, or Nylon Adjusting the Curl PAD Adjusting the BackrestAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart Tightening the Cables Troubleshooting and MaintenanceRetighten the 1/2 Plain Nut down onto the 1/2 Flat Washer Right Arm Cable Diagrams Weight Cable Cable ID Stack Page Part No R0103A Ordering Replacement Parts For That Assembly Stage Pulley 27 Not shown to scale 2 Pulley 24 Not shown to scale R0103A X 3 1/4 Bolt 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Key Exploded