Ordering Replacement Parts, Part No R0103A | Weider WESY59101

ORDERING REPLACEMENT PARTS

To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre- pared to give the following information:

1. The MODEL NUMBER of the product (WESY59101)

2. The NAME of the product (WEIDER

® 9600 PRO weight system)

3.The SERIAL NUMBER of the product (see the front cover of this manual)

4.The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING attached at the center of this manual).

Part No. 184631 R0103A

Printed in Canada © 2002 ICON Health & Fitness, Inc.

Image 28

Weider WESY59101 user manual Ordering Replacement Parts, Part No R0103A

Contents

QUESTIONS? Model No. WESY59101 Serial NoSerial Number Decal Under Seat Customer HOT Line Table of Contents Limited Warranty Important Precautions Replacement decal Apply the decal in the location shownMake sure all parts are properly tightened Ing down Decal shown Using the weight system Before YOU BeginFor your benefit, read this manual carefully before Decal Assembly Cable AssemblyArm Assembly To open the parts bag for that stage Frame Assembly Assembly Do not tighten the Nylon Locknuts yet Press the Weight Tube Bumper 18 into the Weight Tube See the inset drawingCorner bar of the Press Base Slot Locknuts 50. Do not tighten the Nylon Locknuts yet ARM AssemblyTighten the Nylon Locknuts used in steps Bolt and a 3/8 Nylon Locknut Handles Cable Assembly Able to pivot easilyInsert two 2 Square Inner Caps 28 into the Leg Lever 101 Trap is turned to hold the Cable in place Hold the Cable in place Frame 9. Attach a 3/8 Flat Washer 48 and a Plates 23 with a 3/8 x 2 Bolt 54 and a 3/8Nylon Locknut Wrap the Ab Pulley 47 around another 3 1/2 Weight Cable has a bolt, and the other End has a ball on it Be sure Weight Cable is in the groove of the 3 1/2 Pulley Wrap the Weight Cable 72 around a 3 1/2 Pulley Cable Trap is turned to hold the Cable in place4 Bolt 57 and a 3/8 Nylon Jamnut Cable in place Be sure that Cable Trap is turned to hold the Cable in place Remove the preassembled 3/8 x 1 3/4 Bolts Do not tighten the Nylon Locknut yet To hold the Cable in place Be surePlace Hold the Cable 75 in place Seat Assembly Locate and open the parts bag labeled Seat Assembly Maintenance on ADJUSTMENTS, beginning on page 21 of this manualWelded Adjustments Attaching the LAT BAR or AB Strap to High Pulley StationAb Strap 81 can be attached in the same manner Attaching the LAT BAR, AB STRAP, or Nylon Adjusting the Curl PAD Adjusting the BackrestAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart Tightening the Cables Troubleshooting and MaintenanceRetighten the 1/2 Plain Nut down onto the 1/2 Flat Washer Cable Diagrams Right Arm Weight Cable Cable ID Stack Page Ordering Replacement Parts Part No R0103A For That Assembly Stage R0103A Pulley 27 Not shown to scale 2 Pulley 24 Not shown to scale X 3 1/4 Bolt 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Key Qty Exploded