Whirlpool GERC4110PB2 manual Warming Drawer, To Program Steps 2, 3 and 4 of the Sequence

NOTE: If START is pressed after only one sequence has been programmed, a regular cooking mode will start. For example, if you chose BAKE as your first step, and START is pressed, the oven will begin a normal baking cycle. After START has been pressed, additional steps cannot be added to the sequencing. If additional steps are desired, press OFF/CANCEL. This will exit the sequence program, and the oven display will return to just the time of day.

To Program Steps 2, 3 and 4 of the Sequence:

1.Press ADD STEP.

“SELECT COOK OPTION” will appear on the display.

2.Choose a desired cook function by pressing any cook function key. For example, BROIL.

3.Select a desired temperature (optional).

4.Set the cook time by pressing the HOUR and/or MIN pads.

“PUSH START OR ADD STEP” will appear on the oven display.

If you choose to press START, your program sequence will begin. Additional steps cannot be added to the sequence once START has been pressed.

If you choose to add an additional step, press ADD STEP. “SELECT COOK OPTION” will appear on the oven display.

5.Continue repeating steps 1 through 4 until the maximum number of sequences have been set. You can program up to 4 cooking functions within the sequence.

To Review/Modify Programmed Sequence:

If program steps are partially or completely programmed, yet the sequence has not been started, the programmed cook functions can be reviewed.

1.Press REVIEW STEPS. Step 1 will appear in the display.

Subsequent presses of REVIEW STEPS will cause display of programmed steps in order.

“STEP” and “REVIEW” will appear on the display. The number of the displayed step will flash. A recalled step will remain lit on the display for 5 minutes if no further action is taken.

2.If fewer than 4 steps have been programmed, press REVIEW STEPS if it is desired to program an additional step.

3.After Review/Modification of the programmed sequence is complete, press START to begin sequence.

To Modify Sequence Programming:

1.Press DELETE STEP.

The last step of the sequence will be canceled, and the step prior to the canceled sequence will show on the display for either review or modification.

If the programmed sequence has not been started, see “To Program Steps 2, 3 and 4 of the Sequence” section to program a step to replace the canceled cook function.

2.Press START. The first step will show on the display, and the program sequence will begin.

Changes can be made during a programmed cook function; however, changes cannot be made after a programmed cook function has been completed.

If at any time during an active sequenced program ADD STEP is pressed, 3 invalid tones will sound.

Warming Drawer

(on some models)

WARNING

Food Poisoning Hazard

Do not let food sit for more than one hour before or after cooking.

Doing so can result in food poisoning or sickness.

The Warming Drawer is ideal for keeping hot cooked foods at serving temperature. It may also be used for warming breads and pastries.

Different types of food may be placed in the warming drawer at the same time. For best results, do not hold foods longer than 1 hour. For smaller quantities or heat-sensitive foods, such as eggs, do not hold longer than 30 minutes.

Food must be at serving temperature before being placed in the warming drawer. Breads, pastries, and fruit pies may be heated from room temperature.

Remove food from plastic bags and place in oven-safe container. Cover foods with a lid or aluminum foil.

Do not cover with plastic wrap.

Empty serving dishes and ovenproof dishes can be heated while the warming drawer is preheating.

Before using the warming drawer, wash the tray that lines the bottom of the drawer with soap and water. See “General Cleaning” section.

To Use:

1.Place cooked food(s) in warming drawer.

2.Press DRAWER WARM.

WARM DRAWER will appear on the display.

3.Press START.

WARM DRAWER will appear on the display.

4.Press DRAWER OFF when finished.

The Warming Drawer operates at 170ºF (75ºC) only.

20