TROUBLESHOOTING
Problem | Cause | Remedy | See | |
page | ||||
|
|
| ||
Dolby Digital or DTS | The connected component is not set to | Make an appropriate setting following the operating | — | |
sources cannot be | output Dolby Digital or DTS digital | instructions for your component. |
| |
played. (Dolby Digital | signals. |
|
| |
or DTS indicator in |
|
|
| |
“INPUT MODE” is set to “ANALOG”. | Set “INPUT MODE” to “AUTO” or “DTS”. | |||
the front panel | ||||
display does not light |
|
|
| |
up.) |
|
|
| |
|
|
|
| |
A humming sound is | Incorrect cable connections. | Connect the audio cables firmly. If the problem | — | |
heard. |
| persists, the cables may be defective. |
| |
|
|
|
| |
The volume level | The component connected to the AUDIO | Turn on the power of the component. | — | |
cannot be increased, | OUT (REC) jacks of this unit is turned |
|
| |
or the sound is | off. |
|
| |
distorted. |
|
|
| |
|
|
|
| |
The sound effect | It is not possible to record the sound effect |
|
| |
cannot be recorded. | with a recording component. |
|
| |
|
|
|
| |
A source cannot be | The source component is not connected to | Connect the source component to the DIGITAL | ||
recorded by a digital | the DIGITAL INPUT jacks of this unit. | INPUT jacks. |
| |
recording component |
|
|
| |
Some components cannot record the |
|
| ||
connected to the |
|
| ||
DIGITAL OUTPUT | Dolby Digital or DTS sources. |
|
| |
jack. |
|
|
| |
|
|
|
| |
A source cannot be | The source component is not connected to | Connect the source component to the analog AUDIO | ||
recorded by an | the analog AUDIO IN jacks of this unit. | IN jacks. |
| |
analog component |
|
|
| |
connected to the |
|
|
| |
AUDIO OUT (REC) |
|
|
| |
jacks. |
|
|
| |
|
|
|
| |
The sound field | “MEMORY GUARD” in “SET MENU” | Set “MEMORY GUARD” to “OFF”. | ||
parameters and some | is set to “ON”. |
|
| |
other settings of this |
|
|
| |
unit cannot be |
|
|
| |
changed. |
|
|
| |
|
|
|
| |
This unit does not | The internal microcomputer has been | Disconnect the power cable from the AC wall outlet | — | |
operate properly. | frozen by an external electric shock (such | and then plug it in again after about 30 seconds. |
| |
| as lightning or excessive static electricity) |
|
| |
| or by a power supply with low voltage. |
|
| |
|
|
|
| |
“CHECK SP WIRES” | Speaker cables are | Make sure all speaker cables are connected correctly. | ||
appears in the front |
|
|
| |
panel display. |
|
|
| |
|
|
|
| |
There is noise | This unit is too close to the digital or high- | Move this unit further away from such equipment. | — | |
interference from | frequency equipment. |
|
| |
digital or radio |
|
|
| |
frequency equipment. |
|
|
| |
|
|
|
| |
The picture is | The video source uses scrambled or |
|
| |
disturbed. | encoded signals to prevent dubbing. |
|
| |
|
|
|
| |
This unit suddenly | The internal temperature becomes too | Wait about 1 hour for this unit to cool down and then | — | |
enters the standby | high and the overheat protection circuitry | turn it back on. |
| |
mode. | has been activated. |
|
| |
|
|
|
|
INFORMATION | ADDITIONAL |
|
|