Speaker impedance setting, Turning on the power

Speaker impedance setting

CAUTION

If you are using 4 or 6 ohm speakers, set the impedance to 4 or 6 ohms as follows before turning on the power.

Be sure this unit is in the standby mode.

1Turn off the power to this unit, and while holding down STRAIGHT (EFFECT), press

STANDBY/ON.

This unit turns on, and the ADVANCED SETUP menu appears in the front panel display.

STRAIGHT

While holding down, press

2Rotate PROGRAM to move through the menu and select “SP IMP.”.

PROGRAM

CONNECTIONS

Turning on the power

When all connections are complete, turn on the power of this unit.

STANDBY/ON

SYSTEM POWER

PREPARATION

3Press STRAIGHT (EFFECT) repeatedly to select “4 ! MIN”.

STRAIGHT

4Press STANDBY/ON to turn off the power.

The setting you made is reflected the next time this unit’s power is turned on.

Press STANDBY/ON (or SYSTEM POWER on the remote control) to turn on the power of this unit.

SYSTEM

POWER

Front panel

Remote control

English

Page 23

Image 23

Yamaha RX-V557 Speaker impedance setting, Turning on the power, Rotate Program to move through the menu and select SP IMP

Contents

RX-V557 Special Instructions for U.K. Model For U.K. customers Contents Other features FeaturesBuilt-in 6-channel power amplifier Sound field features Please check that you received all of the following parts Supplied accessoriesInstalling batteries in the remote control Getting Started Front panel Controls and Functions Speakers A/B VolumePRESET/TUNING Edit Input Mode Remote control Using the remote control Front panel display Zone 2 indicator 96/24 indicatorLFE indicator Input channel indicators/speaker indicators AC Outlets Rear panel Speaker placement Speaker Setup Speaker connections Tighten the knob to secure the wireOhms before using see Surround Back terminals Front terminalsConnect surround speakers 6, 7 to these terminals Subwoofer jack Connections Before connecting components Connections for DVD playback Connecting video components Connecting to the Multi CH Input jacks Video AUX jacks on the front panel Connections for other video components Connections for audio components Connecting audio components Snap the cover into place Connecting the FM and AM antennasInsert the cable Wire into the slot Clamp it with Pliers Memory back-up Connecting the power supply cordConnecting the AC power cord AC Outlets Switched Rotate Program to move through the menu and select SP IMP Speaker impedance settingTurning on the power Press STANDBY/ON to turn off the power Using the Basic Setup menu Basic Setup Press Enter to confirm your selection Press d to display SET/CANCELPress d to display the Speakers parameter Press j / i to select the number of speakers you connected Perform the following steps after see To balance the speaker levels Select the input source Adjust the volume to the desired output levelPlayback Basic operations Silent Cinema To listen with headphonesTo adjust the tone Select a sound field program if desired Front panel operation Selecting sound field programsSelecting Multi CH Input Playing video sources Background Decoders select with j Remote control operationEnjoying multi-channel software Auto Auto Enjoying 2-channel software in surround Press Select on the remote control to select the decoderWhen you select the SUR. Standard program When you select the SUR. Enhanced or Movie Theater program Night listening modes This adjusts the level of compressionListening to high fidelity stereo sound Direct Stereo Virtual Cinema DSP Listening to unprocessed input signalsDownmixing to 2 channels Displaying information about the input Source Selecting input modesRotate Input to select the input source Automatic and manual tuning FM/AM Tuning Hold down the button to continue searching Presetting stationsManual tuning Automatically presetting FM stations Tune into a station Manually presetting stationsAutomatic preset tuning options Press and hold Memory MAN’L/AUTO FM for more than 3 seconds Repeat steps 1 to 5 to store other stations Selecting preset stationsShows the displayed station has been stored as C3 Press and hold PRESET/TUNING Edit for more than 3 seconds Exchanging preset stationsSelect preset station E1 See Selecting preset stations Receiving Radio Data System stations Do not press FREQ/TEXT until a Radio Data System indicator Changing the Radio Data System mode Selected program type appears in the front panel display PTY Seek function EON function To cancel this function Recording Special considerations when recording DTS software For movie/video sources Sound Field Program Descriptions SUR. Standard Hall in Vienna For music sources Amount of time Using the sleep timerSetting the sleep timer Canceling the sleep timer Advanced Operations Control range is from +10 dB to -10 dB Manually adjusting speaker levelsPress j / i to adjust the speaker output level Press Enter when you have completed your adjustment SET Menu Using SET Menu Center speaker Center Speaker settings Aspeaker SETSubwoofer phase Swfr Phase Front speakers Front Speaker distances Speaker level BSP LevelSpeaker distance CSP Distance Unit Unit Tone bypass TC.BYPASS Audio settings Gaudio SETAudio delay A. Delay Muting type Mute TYP Video conversion V. Conv Display settings Adisplay SET Dimmer Dimmer Parameter initialization CPARAM. INI Speaker B setting SP B Press STANDBY/ON to confirm your selection Advanced Setup MenuAdvanced Setup menu is displayed in the front panel display Remote Remote Advanced Setup menu itemsFactory presets Preset Speaker impedance SP IMP Controlling other components Remote Control FeaturesControl area Controlling this unit Transmit indicator on the remote control flashes twice Setting remote control codesRemote Control Code Default Settings Press Code SET using a ballpoint pen or similar object VCR Controlling other components Enter the code number Switching library codesClearing set up remote control codes Enter the code number 9991 or 9992 see the table below Zone 2 connections System configuration and connections exampleZone Standby Remote controlling Zone For CDs encoded in DTS To turn on all units the main unit and Zone 2 unitSpecial considerations for DTS software For DVDs encoded in DTS Editing Sound Field Parameters What is a sound field Changing parameter settings Use PARAM. INI see Resetting parameters to the factory Presets For 2ch Stereo Direct Direct INIT.DLY Initial delaySound Field Parameter Descriptions DSP Level DSP level For DTS Neo6 Music Image Center image Dimension DimensionFor 6ch Stereo CT Width Center width General Troubleshooting Troubleshooting Digital Output Tuner Remote control Press Straight Effect to select the desired setting Resetting the Factory PresetsAdvanced Setup menu appears in the front panel display Rotate Program to move through the menu and select Preset Audio formats Glossary ITU-R Sound field programsAudio information Cinema DSP Video signal Video signal informationComponent video signal Composite video signal Specifications APPENDIX-i APPENDIX-ii APPENDIX-iii APPENDIX-iv APPENDIX-v All rights reserved

Yamaha RX-V557 owner manual Speaker impedance setting, Turning on the power

Models: RX-V557