Manuals / Zebra Technologies / Computer Equipment / Printer

Zebra Technologies Z4M manual Media Removal

Models: Z4M

1 102

Download 102 pages 62.72 Kb

Page 39

Media supply guide

Transmissive

sensor

Printhead

assembly

Front

housing

assembly

		Dancer	Media
		Dancer	supply
			supply
			hanger
Ribbon	Media
sensor	Media		Take-up
	guide		Take-up
	guide		spindle
			spindle
Printhead	Media		Rewind
open lever	Media		Rewind
open lever	alignment		media
	alignment		media
	spindle		guide

Thumbscrew

Figure 18

Media Removal

1.Cut the media prior to where it winds onto the take-up spindle.

2.Rotate the take-up spindle until the rewind media guide is in the “12 o’clock” position.

3.Loosen the thumbscrew and slide out the rewind media guide to the end of the take-up spindle.

4.Slide the core and roll of media from the take-up spindle.

Zebra Z4M Printer User’s Guide

31

Image 39

Zebra Technologies Z4M manual Media Removal

Contents

Customer order # 77965L Manufacturer 77965LB Rev Zebra Z4M Printer User’s Guide Zebra Z4M Printer Zebra Z4M Printer User’s Guide Table of Contents Establishing Communication Configuration Index Welcome HelloUnpacking and Inspection Media and Ribbon Requirements Reporting DamageStorage Printer Power Printer Overview Purpose Calibrating the PrinterNon-Continuous Web Media Types of MediaContinuous Media Non-Continuous Black Mark MediaChoosing the Print Mode Loading the Media Reflective Sensor Positioning the Media SensorAdjusting the Reflective Sensor Transmissive Sensor Loading the RibbonAuto Calibration Power Switch Operator ControlsFront Panel Configuring the Printer Printing a Test Label Configuring the Software of Printer DriverInterfaces Data SpecificationsEstablishing Communication System ConsiderationsCabling Requirements Printer Basics Front PanelFront Panel Display Key Function Front Panel KeysLight Status Indication Front Panel LightsRoll Media Loading Tear-Off ModeTransmissive Sensor Printhead Assembly Dancer Cutter Mode Printhead Assembly Ribbon Sensor Cutter Value Peel-Off Mode Media supply guide Power Peel-Off Mode Backing Removal Power Rewind Mode Media Removal Fanfold Media Loading Dancer Media Ribbon Media guide Loading the Ribbon Ribbon LoadingZebra Z4M Printer User’s Guide Ribbon Removal Entering the Setup Mode ConfigurationChanging Password-Protected Parameters Leaving the Setup Mode Default +0 Configuration and Calibration SequenceSetting Print Parameters Default +10Sensor Select Default Tear-offDefault Web Selections Web, markPrint Width Print MethodListing Printer Information Init Flash MEM Initialize Memory CardInitialize Card Initialize Flash MemoryCalibration Media and Ribbon Sensor CalibrationSensor Profile ManualSetting Baud Setting Communication ParametersSetting Parallel Communications Default ParallelDefault XON/XOFF Setting ParityDefault Even Setting Host HandshakeCommunications Setting Network IDSetting Communications Mode Network IDRange 00 FF Selecting Prefix and Delimiter CharactersControl Prefix Character Range 00-FFDefault Feed Selecting ZPL ModeDefault ZPL Selections ZPL II, ZPL Power-Up and Head Close Parameters Media Power-UpLabel TOP Label Positioning ParametersBackfeed Sequence BackfeedRibbon S LCD AdjustPassword Level WEB S Media SDefault Gateway IP ResolutionDefault Dynamic Default AllLanguage Default EnglishDefault Permanent Save SettingsCleaning Routine Care and AdjustmentsCleaning the Exterior Cleaning the InteriorCleaning the Printhead and Platen Roller Cleaning the Sensors Cleaning the Power Peel-Off Module Cleaning the Value Peel-Off Module Cleaning the Cutter Module Lubrication Printhead Pressure Adjustment Pressure adjustment dials Power Rewind Media Alignment Adjustment Fuse Replacement Error condition Paper OUT TroubleshootingLCD Error Conditions and Warnings Error condition Ribbon OUTError condition Ribbon Error condition Head OpenGeneral print quality issues Print Quality ProblemsWrinkled ribbon Gray lines on blank labels with no consistent patternCalibration Communications ProblemsZebra Z4M Printer User’s Guide Printer Diagnostics Power-On Self TestAdditional Printer Self Tests Cancel Key Self Test Pause Key Self Test Feed Key Self Test Communications Diagnostics Test Loading Factory DefaultsZebra Z4M Printer User’s Guide General Specifications SpecificationsRibbon Specifications Printing SpecificationsOptions Media SpecificationsBar Codes Zebra Programming Language ZPLPower Line Cord Specifications AC Power CordZebra Z4M Printer User’s Guide Appendix Printer Interface Technical InformationSerial Data Communications RS-232 Interface Hardware Control Signal Descriptions RS-485 Interface Parallel Interface Parallel Data CommunicationsZebra Z4M Printer User’s Guide Index Zebra Z4M Printer User’s Guide Zebra Z4M Printer User’s Guide Zebra Z4M Printer User’s Guide