Omni.Net Lite User’s Guide

 

Table 15 AT Command Sets for the Analog Port

 

 

 

 

COMMAND

DESCRIPTION

 

 

 

 

\Zd=<phone

Set a pre-stored phone number for the analog port.

 

number> [/<sub-

d: 0-4

 

address>]

 

<phone number>: Enter up to 32 characters, including digits from 0 to 9, *, #,

 

 

 

 

hyphen ( -), comma (,) and (‘,’). [‘,’] will be ignored.

 

 

<sub-address>: Enter up to 20 ASCII characters ranging from “0-9”,” a-z” and

 

 

“A-Z”.

 

!pA0=n

Set the device type of the analog equipment connected to the analog port.

 

 

p: enter 1 or 2 to specify the analog port.

 

 

n=0: indicates a telephone, telephone with caller ID (type 1), G3 fax or modem

 

 

(default).

 

 

n=2: indicates a telephone with call waiting caller ID (type 2).

 

 

 

 

!pA1=n

p: enter 1 or 2 to specify the analog port.

 

 

n=0: Disable call waiting.

 

 

n=1: Enable call waiting (default).

 

 

 

 

!pId=<phone

Create a list of the phone numbers for incoming call screening on the analog

 

number> [/<sub-

port.

 

address>]

p: enter 1 or 2 to specify the analog port.

 

 

 

 

d=0-4.

 

 

<phone number>: Enter up to 32 characters, including digits from 0 to 9, *, #,

 

 

hyphen ( -), comma (,) and (‘,’). [‘,’] will be ignored.

 

 

<sub-address>: Enter up to 20 ASCII characters ranging from “0-9”,” a-z” and

 

 

“A-Z”.

 

!pOd=<prefix digits>

Create a list of the prefix digits for outgoing call screening on the analog port.

 

 

p: enter 1 or 2 to specify the analog port.

 

 

d=0-2

 

 

 

 

!pP0=n

Set incoming call screen mode for the analog port.

 

 

p: enter 1 or 2 to specify the analog port.

 

 

n=0: Accept all incoming calls (default).

 

 

n=1: Reject all incoming calls.

 

 

n=2: Only accept the calls from the phone number in the list (see !pId=<phone

 

 

number> [/<sub-address>]).

 

 

n=3: Only reject the calls from the phone number in the list (see !pId=<phone

 

 

number> [/<sub-address>]).

 

!pP1=n

Set outgoing call screen mode for the analog port.

 

 

p: enter 1 or 2 to specify the analog port.

 

 

n=0: No restriction (default).

 

 

n=1: Prohibit all outgoing calls.

 

 

n=2: Only accept the calls with the prefix in the pre-defined list (see

 

 

!pOd=<prefix digits>).

 

 

n=3: Only reject the calls with the prefix in the pre-defined list (see

 

 

!pOd=<prefix digits>).

 

!pP2=n

Select CLIP (Calling Line Identification Presentation) or CLIR (Calling Line

 

 

Identification Restriction) for the analog port.

 

 

p: enter 1 or 2 to specify the analog port.

 

 

n=0 indicates you select CLIR and the ISDN switch will not pass your phone

 

 

number to the destination site.

 

 

n=1 indicates you select CLIP and the ISDN switch will pass your phone number

 

 

to the destination site.

Chapter 3 Using AT Commands

60