Husqvarna 13 AWD, 15 C manual Lever for adjustment of cutting height, Seat, Fuelling

Page 17

PRESENTATION

Lever for adjustment of cutting height

With this lever the cutting height can be adjusted to 9 different positions.

Cutting unit with rear ejection,	40-90 mm
Combi-unit,	(1 9/16" - 3 9/16")

Seat

The seat has a jointed attachment on the front edge and can be tipped forward.

The seat can also be adjusted lengthways.

Release the knobs under the seat and adjust it forwards or backwards to the required position.

Lock the adjustment with the wheels.

6004-013H

6004-014

Fuelling

The engine should be run on 85 octane unleaded petrol/gasoline (no added oil). Environmentally adapted alkylate fuel is also recommended.

Do not use petrol that contains methanol.

Do not fill the tank completely, leave an expansion area of at least 2.5 cm (1").

WARNING! Petrol/gasoline is highly inflammable. Observe care and fill up with fuel outdoors (see safety instructions).

6004-015

English – 15

Image 17

Contents Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Dear customer IntroductionTravel and transport on public roads TowingSerial number Good serviceSlope Explanation of SymbolsGeneral use Safety InstructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Transport Location of the controls PresentationPresentation Throttle and Choke lever Presentation Rider 11, 11 CClutch pedal Brake pedal / Parking brakeParking brake Presentation Rider 13 C, 13 AWD, 15 CSpeed limiter Lift lever for cutting unit Cutting unitFuelling Lever for adjustment of cutting heightSeat Before starting DrivingStarting the engine Rider 13 AWDWarm engine Cold engineTo remove cables, reverse order To start an engine with a weak batteryFor Rider 11 and Rider 11 C Driving the machineFor Rider 13 C, Rider 13 AWD and Rider 15 C Cutting tips Stopping the engine Hill start, manual gearboxRelease lever Rider 13 AWD Release lever Rider 13 C, Rider 13 AWD Rider 15 CRear Axle Front AxleMaintenance schedule MaintenanceAvoid using a high pressure washer or a steam cleaner CleaningFront hood Rider Dismantling of the machine hoodsEngine hood Left-hand fender Inspecting the silencerRight-hand fender Checking and adjustment of the steering wires Check and adjust the brakes on Rider 13 C and Rider 15 C Adjusting the brake Rider 11 and Rider 11 CPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 CAdjusting the Parking Brake Rider 13 AWD Replacement of the fuel filter Adjustment of the throttle wireReplacing the air filter Procedures on contact with acid Check the level of the battery acidChecking of the fuel pump’s air filter Fitting the wrong spark plug type can damage the engineInspecting the safety system Rider 13 AWD Check the engine’s cooling air intake Main fuseChecking the tyre pressure Checking the cutting unit’s parallelism Removing the mulching plug Adjustment of the cutting unit’s parallelism for the RiderPlacing in service position Maintenance Rider 11C,13C, 13 AWD,15CService position for BioClip 6017-221 8009-583 8009-122 6017-223 Take care not to get your hand trapped Restoring from service positionChecking the blades Changing the oil LubricationCheck the engine’s oil level Rider 13 C, Rider 15 C Lubrication of belt tensionerLubrication of front wheel bearings Lubrication Rider 11 and Rider 11 CGeneral lubrication Problem Procedure Trouble Shooting ScheduleStorage ServiceWinter storage CoverTechnical Data Electrical system Dimensions Rider 13 CDimensions Rider 15 C EU declaration of conformity Only applies to Europe EU-DECLARATION of ConformityPre-delivery service ServicejournalAfter first 5 hours Work doneWork done Date, mileage, stamp, sign English 115 01