Husqvarna 15 C, 13 AWD Restoring from service position, Take care not to get your hand trapped

Page 42

MAINTENANCE RIDER 11C,13C, 13 AWD,15C

WARNING!

Take care not to get your hand trapped.

8.Lift off the drive belt (1). Then pull out the pin (2).

9. Pull the frame forwards and refit the pin.

1

2

6017-225

6017-226

10.Grasp the front edge of the cutting unit, pull out and raise into the service position.

If the cylindrical bolt, which is now holding the cutting unit is removed, the cutting unit can be lifted off.

Restoring from service position

To leave the service position, reverse the procedures set out in ”Placing in the service position”. Make sure that the cutting unit’s ”lug” enters the loop correctly on the underside of the machine, see diagram.

6017-227

8009-438

40– English

Image 42

Contents Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Travel and transport on public roads IntroductionDear customer TowingGood service Serial numberExplanation of Symbols SlopeSafety Instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Clutch pedal Presentation Rider 11, 11 CThrottle and Choke lever Brake pedal / Parking brakePresentation Rider 13 C, 13 AWD, 15 C Speed limiterParking brake Cutting unit Lift lever for cutting unitLever for adjustment of cutting height SeatFuelling Starting the engine DrivingBefore starting Rider 13 AWDCold engine Warm engineTo start an engine with a weak battery To remove cables, reverse orderDriving the machine For Rider 13 C, Rider 13 AWD and Rider 15 CFor Rider 11 and Rider 11 C Cutting tips Hill start, manual gearbox Stopping the engineRear Axle Release lever Rider 13 C, Rider 13 AWD Rider 15 CRelease lever Rider 13 AWD Front AxleMaintenance Maintenance scheduleCleaning Avoid using a high pressure washer or a steam cleanerDismantling of the machine hoods Engine hoodFront hood Rider Inspecting the silencer Right-hand fenderLeft-hand fender Checking and adjustment of the steering wires Poorly adjusted brakes can result in reduced braking power Adjusting the brake Rider 11 and Rider 11 CCheck and adjust the brakes on Rider 13 C and Rider 15 C Checking the brake Rider 11 and Rider 11 CAdjusting the Parking Brake Rider 13 AWD Adjustment of the throttle wire Replacement of the fuel filterReplacing the air filter Checking of the fuel pump’s air filter Check the level of the battery acidProcedures on contact with acid Fitting the wrong spark plug type can damage the engineInspecting the safety system Rider 13 AWD Main fuse Checking the tyre pressureCheck the engine’s cooling air intake Checking the cutting unit’s parallelism Adjustment of the cutting unit’s parallelism for the Rider Removing the mulching plugMaintenance Rider 11C,13C, 13 AWD,15C Service position for BioClipPlacing in service position 6017-221 8009-583 8009-122 6017-223 Restoring from service position Take care not to get your hand trappedChecking the blades Lubrication Check the engine’s oil levelChanging the oil Lubrication of belt tensioner Rider 13 C, Rider 15 CLubrication Rider 11 and Rider 11 C General lubricationLubrication of front wheel bearings Trouble Shooting Schedule Problem ProcedureWinter storage ServiceStorage CoverTechnical Data Dimensions Rider 13 C Electrical systemDimensions Rider 15 C EU-DECLARATION of Conformity EU declaration of conformity Only applies to EuropeAfter first 5 hours ServicejournalPre-delivery service Work doneWork done Date, mileage, stamp, sign English 115 01