Husqvarna 15 C, 13 AWD manual Cleaning, Avoid using a high pressure washer or a steam cleaner

Page 26

MAINTENANCE

Cleaning

Clean the machine directly after use.

It is much easier to wash off grass cuttings before they dry.

Oily dirt can be removed using a cold degreasing agent. Spray on a thin layer.

Rinse at normal water pressure.

Do not direct the jet towards electrical components or bearings.

Do not rinse hot surfaces, for example, the engine and exhaust system.

It is recommended that you start the engine and run the mower for a short period after cleaning, so that any remaining water is blown off.

Lubricate the machine if necessary after cleaning.

Carry out extra lubrication when the bearings have been exposed to a degreaser or a water jet.

IMPORTANT INFORMATION

Avoid using a high pressure washer or a steam cleaner

There is a major risk of water penetrating into bearings and electrical connections. Corrosion attack can result, which will lead to running problems. Cleaning additives generally aggravate the damage.

8009-741

24– English

Image 26

Contents Rider 11 Rider 11 C Rider 13 C Rider 13 AWD Rider 15 C Page Contents Travel and transport on public roads IntroductionDear customer TowingGood service Serial numberExplanation of Symbols SlopeSafety Instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Location of the controls PresentationPresentation Clutch pedal Presentation Rider 11, 11 CThrottle and Choke lever Brake pedal / Parking brakeParking brake Presentation Rider 13 C, 13 AWD, 15 CSpeed limiter Cutting unit Lift lever for cutting unitFuelling Lever for adjustment of cutting heightSeat Starting the engine DrivingBefore starting Rider 13 AWDCold engine Warm engineTo start an engine with a weak battery To remove cables, reverse orderFor Rider 11 and Rider 11 C Driving the machineFor Rider 13 C, Rider 13 AWD and Rider 15 C Cutting tips Hill start, manual gearbox Stopping the engineRear Axle Release lever Rider 13 C, Rider 13 AWD Rider 15 CRelease lever Rider 13 AWD Front AxleMaintenance Maintenance scheduleCleaning Avoid using a high pressure washer or a steam cleanerFront hood Rider Dismantling of the machine hoodsEngine hood Left-hand fender Inspecting the silencerRight-hand fender Checking and adjustment of the steering wires Poorly adjusted brakes can result in reduced braking power Adjusting the brake Rider 11 and Rider 11 CCheck and adjust the brakes on Rider 13 C and Rider 15 C Checking the brake Rider 11 and Rider 11 CAdjusting the Parking Brake Rider 13 AWD Adjustment of the throttle wire Replacement of the fuel filterReplacing the air filter Checking of the fuel pump’s air filter Check the level of the battery acidProcedures on contact with acid Fitting the wrong spark plug type can damage the engineInspecting the safety system Rider 13 AWD Check the engine’s cooling air intake Main fuseChecking the tyre pressure Checking the cutting unit’s parallelism Adjustment of the cutting unit’s parallelism for the Rider Removing the mulching plugPlacing in service position Maintenance Rider 11C,13C, 13 AWD,15CService position for BioClip 6017-221 8009-583 8009-122 6017-223 Restoring from service position Take care not to get your hand trappedChecking the blades Changing the oil LubricationCheck the engine’s oil level Lubrication of belt tensioner Rider 13 C, Rider 15 CLubrication of front wheel bearings Lubrication Rider 11 and Rider 11 CGeneral lubrication Trouble Shooting Schedule Problem ProcedureWinter storage ServiceStorage CoverTechnical Data Dimensions Rider 13 C Electrical systemDimensions Rider 15 C EU-DECLARATION of Conformity EU declaration of conformity Only applies to EuropeAfter first 5 hours ServicejournalPre-delivery service Work doneWork done Date, mileage, stamp, sign English 115 01